Renesis v2.0

Reply Subscribe

Thread Tools

Rate Thread

Sep 2, 2010 | 03:25 PM

#551

paulmasoner

Asshole for hire

iTrader: (1)

Joined: Jun 2006

Posts: 3,214

Likes: 3

From: Colfontaine, Belgium

Quote:

Originally Posted by Brettus

the guys I'm talkiing about are not average joes

then why are they stuck relying on someone else to do their tuning?

Sep 3, 2010 | 12:21 AM

#552

makristal

Sunlight Silver Bias

Joined: May 2010

Posts: 1,259

Likes: 0

From: Kirkland, WA

I might join this prestigious club soon!

Sep 3, 2010 | 10:14 AM

#553

Nemesis8

Thread Starter

Bigus Rotus

iTrader: (3)

Joined: Jun 2004

Posts: 8,573

Likes: 1

From: Missouri

The ported renny club? or the Iannetti ceramic seal club?

Sep 3, 2010 | 11:09 AM

#554

shadycrew31

WENTGERMAN

iTrader: (6)

Joined: Apr 2008

Posts: 5,806

Likes: 31

From: Burbs,PA

Please say ported!!!

I'm not balller enough to have Iannetti ceramic seals...

Sep 3, 2010 | 11:18 AM

#555

dondo

100% baller (finally!)

iTrader: (7)

Joined: Jun 2007

Posts: 5,385

Likes: 2

From: Seattle, WA

The new motor club, not quite as baller as Nemesis. His lowest rotor face was 5.0 at 250 on Kevin's tester.

Sep 3, 2010 | 11:46 AM

#556

Nemesis8

Thread Starter

Bigus Rotus

iTrader: (3)

Joined: Jun 2004

Posts: 8,573

Likes: 1

From: Missouri

Wow - 5 is low

That tester has done a good service

Sep 3, 2010 | 12:02 PM

#557

zoom44

Administrator

Joined: Jul 2002

Posts: 21,958

Likes: 115

From: portland oregon

Quote:

Originally Posted by Nemesis8

The REVi bell mouth tube and MAF housing. I like what RB did here.

you know, richard makes the maf housing. he might even make the "bell"

Sep 3, 2010 | 12:24 PM

#558

makristal

Sunlight Silver Bias

Joined: May 2010

Posts: 1,259

Likes: 0

From: Kirkland, WA

I'm hoping it will post the same results at University Mazda on Tuesday.....

I NEED HOPE!!!

Sep 3, 2010 | 03:29 PM

#559

pdxhak

Official Post Whore

iTrader: (2)

Joined: Jan 2003

Posts: 10,462

Likes: 32

From: Portland,OR

Quote:

Originally Posted by Nemesis8

Wow - 5 is low

That tester has done a good service

Sure does! My reman went belly up due to low compression in the rear rotor and your tester showed us that at 600 miles.

Sep 3, 2010 | 04:05 PM

#560

shadycrew31

WENTGERMAN

iTrader: (6)

Joined: Apr 2008

Posts: 5,806

Likes: 31

From: Burbs,PA

I need mine tested like whoa.

Sep 3, 2010 | 08:31 PM

#561

makristal

Sunlight Silver Bias

Joined: May 2010

Posts: 1,259

Likes: 0

From: Kirkland, WA

The only trick is to make sure that University Mazda won't try to screw me over.

Sep 3, 2010 | 10:18 PM

#562

Nemesis8

Thread Starter

Bigus Rotus

iTrader: (3)

Joined: Jun 2004

Posts: 8,573

Likes: 1

From: Missouri

Quote:

Originally Posted by shadycrew31

I need mine tested like whoa.

what's your 20?

Sep 3, 2010 | 10:25 PM

#563

Nemesis8

Thread Starter

Bigus Rotus

iTrader: (3)

Joined: Jun 2004

Posts: 8,573

Likes: 1

From: Missouri

DEI REVi Intake

Not sure if I will use this, but it does have 850F wrap on it now...

Attached Thumbnails

Sep 4, 2010 | 03:42 AM

#564

shadycrew31

WENTGERMAN

iTrader: (6)

Joined: Apr 2008

Posts: 5,806

Likes: 31

From: Burbs,PA

Quote:

Originally Posted by Nemesis8

what's your 20?

SoCal.

BHR quoted me for a compression test at SS but the figure was a bit above what I'm willing to spend.

I'm most likely going to take a day off work to get my compression tested then get my PCM.

Sep 4, 2010 | 03:47 AM

#565

FoxeyL8y

Derp Kitten

Joined: Jun 2010

Posts: 1,362

Likes: 5

From: Seattle, WA

Quote:

Originally Posted by dondo

The new motor club, not quite as baller as Nemesis. His lowest rotor face was 5.0 at 250 on Kevin's tester.

i wish i coulda been there and tested mine

Sep 4, 2010 | 09:39 AM

#566

makristal

Sunlight Silver Bias

Joined: May 2010

Posts: 1,259

Likes: 0

From: Kirkland, WA

Yeah, but now all I've been thinking of is "What is my engine passes by a tiny margin...What should I do with it?"

Sep 4, 2010 | 10:51 AM

#567

Razz1

Mu ha.. ha...

Joined: Aug 2004

Posts: 14,361

Likes: 3

From: Cali

I'm anixous to see the dyno results.

Sep 4, 2010 | 11:08 AM

#568

shadycrew31

WENTGERMAN

iTrader: (6)

Joined: Apr 2008

Posts: 5,806

Likes: 31

From: Burbs,PA

well considering crh put down 212? whp 2 years ago at dyno day I'm not thinking we will do any better than 215 at the most.

Sep 5, 2010 | 11:42 AM

#569

Nemesis8

Thread Starter

Bigus Rotus

iTrader: (3)

Joined: Jun 2004

Posts: 8,573

Likes: 1

From: Missouri

My folder is alive!! Downloading first tune now.

Sep 5, 2010 | 02:15 PM

#570

Nemesis8

Thread Starter

Bigus Rotus

iTrader: (3)

Joined: Jun 2004

Posts: 8,573

Likes: 1

From: Missouri

Rev 1 of my tune is loaded, and the car already feels better under my foot. My idle still lacks the velvet smoothness of the REVi tough... But I will finish and dyno tune the AEM first.

Attached Thumbnails

Sep 5, 2010 | 02:20 PM

#571

Nemesis8

Thread Starter

Bigus Rotus

iTrader: (3)

Joined: Jun 2004

Posts: 8,573

Likes: 1

From: Missouri

Outside

Attached Thumbnails

Sep 6, 2010 | 12:40 AM

#572

InfiniFC

Rotarydude

iTrader: (8)

Joined: Jan 2002

Posts: 117

Likes: 0

From: Union City, CA

Quote:

Originally Posted by Nemesis8

My folder is alive!! Downloading first tune now.

Sweet Nemesis... Looking forward to seeing the results!

Sep 6, 2010 | 10:36 PM

#573

Nemesis8

Thread Starter

Bigus Rotus

iTrader: (3)

Joined: Jun 2004

Posts: 8,573

Likes: 1

From: Missouri

Renesis v3.0

Winter is coming...

Attached Thumbnails

Sep 6, 2010 | 11:51 PM

#574

Brettus

Boosted Kiwi

iTrader: (2)

Joined: Apr 2006

Posts: 20,844

Likes: 1,798

From: Y-cat-o NZ

wha ?

Sep 7, 2010 | 11:05 AM

#575

Nemesis8

Thread Starter

Bigus Rotus

iTrader: (3)

Joined: Jun 2004

Posts: 8,573

Likes: 1

From: Missouri

Quote:

Originally Posted by Brettus

wha ?

Man cannot live on one engine alone

This will be my turbo build, and I will go slow on it. I just need to arm wrestle with my buddy up North a bit to buy his junk in the garage that he is not using...

Thread Tools

Show Printable Version

Email this Page

Rate This Thread