waterproofone

the one closest to the battery..whether it be the ssv or apv..it's the one that is weak and I need to clean it or such, it's sticking. I am pretty sure it's gummed up and in the winter it just makes it that much more sticky/tacky inside.

I will look for the post on the topic.

Mr.Rexx

question:
Just got my MM calibration not to long ago. Didn't notice it before but over 7K engine is noticeably losing it's power and I can hear constant "poping" from the exhaust... Any ideas?

MazdaManiac

iTrader: (3)

You are still on v4.0.1.

Mr.Rexx

I installed the whatever calibration you gave me and yes, I think it is a v4.0.1. is there a v4.0.2.?

MazdaManiac

iTrader: (3)

Did you read the instructions in the e-mail that announced your download of v4.0.1?

Sorry to answer a question with a question.

Mr.Rexx

Should I send you my new logs?

Mr.Rexx

Sorry, never got an e-mail after I downloaded it.

Mr.Rexx

ok, I just went to check and... It looks like I should be sending you some more logs with the
v4.0.1...

Mr.Rexx

honestly that e-mail looked so much like the first one that I didn't finish reading it... My bad. I'm sorry. Thanks!

alz0rz

iTrader: (41)

Consolidate>.<

MazdaManiac

iTrader: (3)

I wonder why I bother...

Clearly, they are NOT identical:

L337fpc

iTrader: (4)

Hey Jeff,

Hows the queue looking? Any idea on when the next round of maps will be sent out?

MazdaManiac

iTrader: (3)

Just starting back again since we stopped for the holidays on the 21st.

I have a backlog of about 80 calibrations. (I'm getting about 30 submissions a week.)

L337fpc

iTrader: (4)

Good Deal, thanks for the quick response.

Huey52

iTrader: (2)

I ***-umed they were identical emails as well - which made an ***-outta-me!

PhantomRX-8

iTrader: (1)

Ya if you dont have any CELs. I just ran through inspection less than an hour ago and she passed with flying colors. Granted I had to put the stock midpipe back on and Im on a tune that I made until I get to AZ so Jeff can dial it in, but I dont have anything masked except P0411. If your car runs good, shouldnt have any problems.

MazdaManiac

iTrader: (3)

You don't need the stock midpipe, the CAT, the air pump the rear O2 sensor or any of the other emissions gear to pass.
Hell, I can make it so you can show up without the MOTOR and still pass.

PhantomRX-8

iTrader: (1)

My car smells VERY rich w/o the cat even though it shows 14.7-15.0 on the wideband. They sniff test out here so I wasnt sure if they would flag me since more fuel is making its way out the pipe without the cat. Just didnt want to be fined for removing emmissions bull ****.

MazdaManiac

iTrader: (3)

Un-CATted rotary exhaust stinks, lean or rich.
So does rotary exhaust WITH a CAT. lol

dannobre

iTrader: (3)

So when you mask the CEL's it allows the test modes to set properly ??

I will likely have to pass emissions next year...so this might be an easy way to pass??

PhantomRX-8

iTrader: (1)

Lol!! Good point! Although it was kinda cool sitting at the intersection today and not being the smelly car for once!! Was thinking about leaving it in but I lost 30 MAF A/D counts with it on, (went from 339 to 309) so its gonna come off. My cousin Shaun gave me your number (hope thats ok). Ill text you when I get out there to see how your schedule is for getting together and tuning the car.

MazdaManiac

iTrader: (3)

Yes. If the PID is turned off, it doesn't flag the readiness switch.

I dunno what happened with Shaun's car (he had a failed rear sensor), but I've taken that sensor completely out and had it set the readiness flag as "go".

Nemesis8

iTrader: (3)

When I get the street ported motor in this Spring, can I start with your dyno tune map on my car and tune from there? All the bolt-ons will be the same.

MazdaManiac

iTrader: (3)

Maybe, but probably not.
Try it and see what it does!

onefatsurfer

I'm going to have to get my car re-inspected in May. They're a real bitch around here when it comes to emissions, so I'm going to put my cat back on and uninstall the AP. How long should I drive it around before everything is re-learned so that it doesn't trigger anything when I go to inspection?