Aggressive Wheel Fitment Thread
#9004
O' Let's do it.
iTrader: (3)
I'm on H&R springs and my car is pretty low.
Not everyone wants the harsh ride of high spring rates you get associated with coilovers, nor has the money to drop on expensive coilovers that do yeild a decent ride for street.
I'm assuming he didn't preload properly or perhaps even got some Tein knock-offs.
Try loosening the bolts again and drive around the block. Come back and tighten it up.
My method of preloading is to loosen the arms, drive onto the alignment rack and jounce the suspension several times before re-tightening the arms. Works like a champ!
Alternatively, putting a floor jack under the knuckle and re-tightening is the most practical solution.
Not everyone wants the harsh ride of high spring rates you get associated with coilovers, nor has the money to drop on expensive coilovers that do yeild a decent ride for street.
I'm assuming he didn't preload properly or perhaps even got some Tein knock-offs.
Try loosening the bolts again and drive around the block. Come back and tighten it up.
My method of preloading is to loosen the arms, drive onto the alignment rack and jounce the suspension several times before re-tightening the arms. Works like a champ!
Alternatively, putting a floor jack under the knuckle and re-tightening is the most practical solution.
#9006
Bat Mobile Driver
now this is what you call aggressive wheel fitment!!!!!
Kawashima Celica leaving the 2012 Nagoya Exciting Car Showdown
sorry its not a rx8 but i thought i would share with everyone
Kawashima Celica leaving the 2012 Nagoya Exciting Car Showdown
sorry its not a rx8 but i thought i would share with everyone
#9007
Lewisville, TX
Join Date: Jan 2011
Location: Dallas, TX
Posts: 89
Likes: 0
Received 0 Likes
on
0 Posts
#9008
I was going into a parking lot tonight, at an angle of course, and one of my tires went over a manhole and started spinning and got stuck. Then I realized that my wheels were locked against the frame cause of my stupid amounts of width up front. Had to really gas is to get off that manhole, traction control and wheel hop all kinds.
I think my alignment is wonky now lol
I think my alignment is wonky now lol
#9009
ROTARYPOWER.es
Hi guys,
anyone know an alternative to ADVAN MODEL 5? cheaper if are possible. these wheels are discontinued.
I find some models, but are unviable for cost reasons :
Adv1 05.1
Prodrive GC-05k
Vossen VVSCV5
HRE P47SC
anyone know an alternative to ADVAN MODEL 5? cheaper if are possible. these wheels are discontinued.
I find some models, but are unviable for cost reasons :
Adv1 05.1
Prodrive GC-05k
Vossen VVSCV5
HRE P47SC
#9010
Registered
iTrader: (7)
Join Date: Jun 2009
Location: so.cal
Posts: 825
Likes: 0
Received 0 Likes
on
0 Posts
might not be the place to put it, but my wheels are for sale for them 626 socal locals that want to get fitted. white varrstoen 2.2.1 WITH tires. kit is also for sale
18x10.5+15 w/ 265/35 square setup
extreme dimensions INGS front paired with shine FEED sides both painted WWP
18x10.5+15 w/ 265/35 square setup
extreme dimensions INGS front paired with shine FEED sides both painted WWP
#9011
Danny Rotstein
iTrader: (10)
Join Date: Dec 2009
Location: Chicago
Posts: 1,325
Likes: 0
Received 0 Likes
on
0 Posts
xxr 522, they do make them in 17's yes. Just know that the smaller sizes aren't as wide so they wont be as concave.
Maybe if you sold your wheels to me a while ago this wouldn't have happened. LOL... totally kidding. That sucks man, hope you didnt bend a lower control arm
seen your car around online, looks real good man! I need FEED sides
Whats the next setup gonna be?
might not be the place to put it, but my wheels are for sale for them 626 socal locals that want to get fitted. white varrstoen 2.2.1 WITH tires. kit is also for sale
18x10.5+15 w/ 265/35 square setup
extreme dimensions INGS front paired with shine FEED sides both painted WWP
18x10.5+15 w/ 265/35 square setup
extreme dimensions INGS front paired with shine FEED sides both painted WWP
Whats the next setup gonna be?
#9012
Registered
iTrader: (7)
Join Date: Jun 2009
Location: so.cal
Posts: 825
Likes: 0
Received 0 Likes
on
0 Posts
hahah thanks! buy my sides!!! i needa get rid of them >.>
hmmmm what's next?? ima pick up a set of equips, 18x10+18 w/ 15mm all around right after the varrstoens sell and i'm going to keep it stock body. saw a BB from japan on speedhunters a while back. stock body on vip modulars....ohbaby that thing was sick. so simple, yet so clean. going to try to do something like that
hmmmm what's next?? ima pick up a set of equips, 18x10+18 w/ 15mm all around right after the varrstoens sell and i'm going to keep it stock body. saw a BB from japan on speedhunters a while back. stock body on vip modulars....ohbaby that thing was sick. so simple, yet so clean. going to try to do something like that
#9013
Danny Rotstein
iTrader: (10)
Join Date: Dec 2009
Location: Chicago
Posts: 1,325
Likes: 0
Received 0 Likes
on
0 Posts
hahah thanks! buy my sides!!! i needa get rid of them >.>
hmmmm what's next?? ima pick up a set of equips, 18x10+18 w/ 15mm all around right after the varrstoens sell and i'm going to keep it stock body. saw a BB from japan on speedhunters a while back. stock body on vip modulars....ohbaby that thing was sick. so simple, yet so clean. going to try to do something like that
hmmmm what's next?? ima pick up a set of equips, 18x10+18 w/ 15mm all around right after the varrstoens sell and i'm going to keep it stock body. saw a BB from japan on speedhunters a while back. stock body on vip modulars....ohbaby that thing was sick. so simple, yet so clean. going to try to do something like that
How much for sides?
edit: and why not go wider? wiiide equips are amazing.
#9014
Registered
iTrader: (7)
Join Date: Jun 2009
Location: so.cal
Posts: 825
Likes: 0
Received 0 Likes
on
0 Posts
I thought about going x11's but decided not to cause, from my understanding of wheels, I can get bigger lips on a x10 and lower offset. And my buddy is hooking me up with equips for cheap.
I'm asking 200 for the sides. No serious cracks or scratches or anything like that. Paint is perfect. too bad your car isn't white lol
I'm asking 200 for the sides. No serious cracks or scratches or anything like that. Paint is perfect. too bad your car isn't white lol
#9015
Danny Rotstein
iTrader: (10)
Join Date: Dec 2009
Location: Chicago
Posts: 1,325
Likes: 0
Received 0 Likes
on
0 Posts
I thought about going x11's but decided not to cause, from my understanding of wheels, I can get bigger lips on a x10 and lower offset. And my buddy is hooking me up with equips for cheap.
I'm asking 200 for the sides. No serious cracks or scratches or anything like that. Paint is perfect. too bad your car isn't white lol
I'm asking 200 for the sides. No serious cracks or scratches or anything like that. Paint is perfect. too bad your car isn't white lol
#9017
05 RX8 Sold///05 Evo VIII
iTrader: (5)
Join Date: Feb 2009
Location: New Berlin, WI
Posts: 457
Likes: 0
Received 0 Likes
on
0 Posts
Lol. There's so much off topic banter in this thread it's sick.
Everyone wants to be Mr. Badass behind a keyboard and pick apart posts to "one-up" someone. Soooo childish.
But I chuckled at your reply Tazfc3s.
Dlum I'm not really a huge fan of white wheels but I love white cars, yours pulls it off nicely! I wish mine was WWP
Everyone wants to be Mr. Badass behind a keyboard and pick apart posts to "one-up" someone. Soooo childish.
But I chuckled at your reply Tazfc3s.
Dlum I'm not really a huge fan of white wheels but I love white cars, yours pulls it off nicely! I wish mine was WWP
#9018
Drift Happens
iTrader: (2)
Lol. There's so much off topic banter in this thread it's sick.
Everyone wants to be Mr. Badass behind a keyboard and pick apart posts to "one-up" someone. Soooo childish.
But I chuckled at your reply Tazfc3s.
Dlum I'm not really a huge fan of white wheels but I love white cars, yours pulls it off nicely! I wish mine was WWP
Everyone wants to be Mr. Badass behind a keyboard and pick apart posts to "one-up" someone. Soooo childish.
But I chuckled at your reply Tazfc3s.
Dlum I'm not really a huge fan of white wheels but I love white cars, yours pulls it off nicely! I wish mine was WWP
#9019
How the hell do you fit the rear offset? I have 18x10 +5 the rim sticks out way past the guard