Pettit Super Charger Owners
, the flash and some meth...
Again, the a/t must suffer and endure - no flash for us
11-03-2007, 10:54 AM
#308
Registered User
iTrader: (1)
Join Date: Jun 2007
Location: Houston, TX
Posts: 1,112
Likes: 0
Received 0 Likes
on
0 Posts
Drove the car this morning after clearing the P2119 code for about 30 minutes with no problems at all. I drove it slow, fast, cruising, like you stole it mode and everything worked OK. Got home, let is sit for an hour, crank and same thing P2119 code and back to 3k rpms. Turned it off, clear code, crank and no problems at all. This is driving me crazy
Any more suggestions?
11-03-2007, 12:32 PM
#309
Pettit fangurl <3
Join Date: Mar 2005
Location: Aston, PA
Posts: 5,386
Likes: 0
Received 0 Likes
on
0 Posts
11-03-2007, 04:23 PM
#313
Registered User
Join Date: Nov 2007
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
hood
Im looking to get a Carbon fiber Hood for my 04, titaniam gray rx8....know of and good companies that make a good one...I am afraid that after i order it and go to put it on that it might not fit well.....If you know of any i would really appreciate it.
11-03-2007, 04:35 PM
#314
How about you post this request in the Exterior & Body Kit forum. I'm sure you will get a better response - This is the Pettit Super Charger Owners forum. If you don't get a response in the proper forum in a reasonable length of time, PM me and I will get you the help you need.
11-03-2007, 05:40 PM
#315
Surf Hard, Drive Hard
Join Date: Feb 2007
Location: Indialantic, Florida
Posts: 7,840
Likes: 0
Received 11 Likes
on
9 Posts
Juan,
If you need the service manuals, PM me with your home E-mail and I'll send them. I don't know if they are still available online or not, but I have them all.
If you need the service manuals, PM me with your home E-mail and I'll send them. I don't know if they are still available online or not, but I have them all.
11-03-2007, 09:08 PM
#317
Registered User
iTrader: (1)
Join Date: Jun 2007
Location: Houston, TX
Posts: 1,112
Likes: 0
Received 0 Likes
on
0 Posts
Still here. I cleaned the throttle contacts and so far no P2119 trouble code. I'll let it sit overnight and see what happens tomorrow. The problem is that I can't drive the car around because it doesn't have the nose. I purchased a RB Type II nose and after less than a week on the car I had a little encounter with wet grass and a pond. To long of a story to tell but it had to do with semi bald tires, cold tires, traction control off and not getting used to the additional power. Anyways, I got new rubber all the way around and the nose has been sitting at the body shop for over three weeks and waiting for it. The person that painted the nose and currently working on it is JD's Paint and Body shop, he is featured in the Mopar Muscle Magazine and a very nice guy. Hopefuly I'll get the nose next week since I would like to run an AutoX next Saturday in Orlando.
11-03-2007, 09:12 PM
#318
Registered User
iTrader: (1)
Join Date: Jun 2007
Location: Houston, TX
Posts: 1,112
Likes: 0
Received 0 Likes
on
0 Posts
Moon, let Cam know that as soon as I get my car going (need the nose back from the body shop) I'm going to give him a call to set up a day to take my car down to the shop.
11-03-2007, 09:15 PM
#319
Surf Hard, Drive Hard
Join Date: Feb 2007
Location: Indialantic, Florida
Posts: 7,840
Likes: 0
Received 11 Likes
on
9 Posts
Well.....before your little fishing expedition.....how was the fitment of the RB II nose? I was thinking about that whole kit at one time. Hopefully you didn't mess it up too terribly bad.
Ouch! Nevermind......I just saw the pics in the other thread!
Ouch! Nevermind......I just saw the pics in the other thread!
Last edited by Mazurfer; 11-03-2007 at 09:20 PM.
11-03-2007, 09:17 PM
#320
Registered User
iTrader: (1)
Join Date: Jun 2007
Location: Houston, TX
Posts: 1,112
Likes: 0
Received 0 Likes
on
0 Posts
RB Type II Nose
See below before and after accident pix per comment above.
Thank God I miss the three palm trees in front and no damage to the car except for the nose.
Thank God I miss the three palm trees in front and no damage to the car except for the nose.
Last edited by marsredr100; 11-29-2007 at 05:41 PM.
11-03-2007, 09:21 PM
#321
Registered User
iTrader: (1)
Join Date: Jun 2007
Location: Houston, TX
Posts: 1,112
Likes: 0
Received 0 Likes
on
0 Posts
I haven't decide if to get the RB skirt and wing or a the MS one.
11-03-2007, 11:19 PM
#323
One suggestion:
For the home install----a complete vacuum line diagram of the new way to route and the sites to attach them would be extremely helpful. Like the wiring diagrams in detail.
questions:
1- (she is almost ready to crank) what is the hose that is attached to a 90degree fitting on the front part of the compressor , pointing toward the firewall for?
it has to be a breather tube for the compressor? What do I do with this hose?
2- do I need to attach a vacuum line to the by pass/regular ?
3- the vacuum line (male extension) off the bottom rearmost part of the manifold/cmpressor (cant really tell) it appears that a hose goes from there to the air intake before the TB?
Other than those few things---its been no problem.
I routed the a/w intercooler line (the LONG one to a 90 degree turn coming off the unit and down the side of the engine bay and then through and over the radiator and used another 90 degree fitting to attach to the cooler itself. So that part of the engine bay has been decluttered a little.
I know I know -----Pictures----soon as I have time guys---a lot is going on now along with the backyard install.
The wife has breast reconstruction surgery Monday and we have been picking out new ones. Thank God her cancer is gone.
olddragger
For the home install----a complete vacuum line diagram of the new way to route and the sites to attach them would be extremely helpful. Like the wiring diagrams in detail.
questions:
1- (she is almost ready to crank) what is the hose that is attached to a 90degree fitting on the front part of the compressor , pointing toward the firewall for?
it has to be a breather tube for the compressor? What do I do with this hose?
2- do I need to attach a vacuum line to the by pass/regular ?
3- the vacuum line (male extension) off the bottom rearmost part of the manifold/cmpressor (cant really tell) it appears that a hose goes from there to the air intake before the TB?
Other than those few things---its been no problem.
I routed the a/w intercooler line (the LONG one to a 90 degree turn coming off the unit and down the side of the engine bay and then through and over the radiator and used another 90 degree fitting to attach to the cooler itself. So that part of the engine bay has been decluttered a little.
I know I know -----Pictures----soon as I have time guys---a lot is going on now along with the backyard install.
The wife has breast reconstruction surgery Monday and we have been picking out new ones. Thank God her cancer is gone.
olddragger
11-04-2007, 01:02 AM
#325
One suggestion:
For the home install----a complete vacuum line diagram of the new way to route and the sites to attach them would be extremely helpful. Like the wiring diagrams in detail.
questions:
1- (she is almost ready to crank) what is the hose that is attached to a 90degree fitting on the front part of the compressor , pointing toward the firewall for?
it has to be a breather tube for the compressor? What do I do with this hose?
2- do I need to attach a vacuum line to the by pass/regular ?
3- the vacuum line (male extension) off the bottom rearmost part of the manifold/cmpressor (cant really tell) it appears that a hose goes from there to the air intake before the TB?
Other than those few things---its been no problem.
I routed the a/w intercooler line (the LONG one to a 90 degree turn coming off the unit and down the side of the engine bay and then through and over the radiator and used another 90 degree fitting to attach to the cooler itself. So that part of the engine bay has been decluttered a little.
I know I know -----Pictures----soon as I have time guys---a lot is going on now along with the backyard install.
The wife has breast reconstruction surgery Monday and we have been picking out new ones. Thank God her cancer is gone.
olddragger
For the home install----a complete vacuum line diagram of the new way to route and the sites to attach them would be extremely helpful. Like the wiring diagrams in detail.
questions:
1- (she is almost ready to crank) what is the hose that is attached to a 90degree fitting on the front part of the compressor , pointing toward the firewall for?
it has to be a breather tube for the compressor? What do I do with this hose?
2- do I need to attach a vacuum line to the by pass/regular ?
3- the vacuum line (male extension) off the bottom rearmost part of the manifold/cmpressor (cant really tell) it appears that a hose goes from there to the air intake before the TB?
Other than those few things---its been no problem.
I routed the a/w intercooler line (the LONG one to a 90 degree turn coming off the unit and down the side of the engine bay and then through and over the radiator and used another 90 degree fitting to attach to the cooler itself. So that part of the engine bay has been decluttered a little.
I know I know -----Pictures----soon as I have time guys---a lot is going on now along with the backyard install.
The wife has breast reconstruction surgery Monday and we have been picking out new ones. Thank God her cancer is gone.
olddragger
Taking care of the wife come first and is most likely to only reason I am not screaming for pictures.
I know what your saying about the vaccum lines. Just as I thought that I had them all figured out, Cam came to Vegas (while I was gone on vacation) and changed some and added a couple.
