Greddy turbo install help
#277
Registered
Join Date: Aug 2004
Location: Virginia/Maryland
Posts: 1,294
Likes: 0
Received 0 Likes
on
0 Posts
I didn't have to compeltely remove the engine mount out from the engine bay, just unbolt it from the engine and from the frame, and you can move it around to get it out of your way.
#278
Registered User
still having a little trouble, i think it may just be my own stupidity. This is what I did, unscrewed the three bolts connected to the engine, Unscrew the one bolt on top of the mount where it sits over the frame on the rubber piece, jacked the motor up a little and it is totally free of the engine now but cannot get it out. I noticed there are two bolts on the part that screws directly to the frame, do I take that off to? Thanks guys
Chris
Chris
#279
90% Carbon-100% Power
Join Date: Apr 2004
Location: Thessaloniki,GREECE
Posts: 1,706
Likes: 0
Received 0 Likes
on
0 Posts
Welli started the installation today and i ll finish it tomorrow maybe...But here is what spinning in my mind and i can't sleep...I have canzoomer midp-4 which use a 5" size catalytic system when the stock stystem use a 2" size catalytic...
Well is there any chance to accidentaly increase boost with the highter air flow and have a problem with the turbo running in highter boost??
I also have greddy sp2 and by the time we speak we are connecting the revi with the turbo...
Please help me!!!!
Well is there any chance to accidentaly increase boost with the highter air flow and have a problem with the turbo running in highter boost??
I also have greddy sp2 and by the time we speak we are connecting the revi with the turbo...
Please help me!!!!
#280
90% Carbon-100% Power
Join Date: Apr 2004
Location: Thessaloniki,GREECE
Posts: 1,706
Likes: 0
Received 0 Likes
on
0 Posts
Well here is my biggest problem right now(well one of the probs...)
I have placed the airinix filter in the revi box and i don't have any space under the hood to install the oil catch tank....
Any suggestions??And is there a horizontally oil catch tank???
I have placed the airinix filter in the revi box and i don't have any space under the hood to install the oil catch tank....
Any suggestions??And is there a horizontally oil catch tank???
#283
90% Carbon-100% Power
Join Date: Apr 2004
Location: Thessaloniki,GREECE
Posts: 1,706
Likes: 0
Received 0 Likes
on
0 Posts
i ll post a pic tomorrow to see...grrrrr
i ll probably make a custom box similar to the revi box with glass on top and install the tank and airinix inside it...lot of job...
i ll probably make a custom box similar to the revi box with glass on top and install the tank and airinix inside it...lot of job...
#284
90% Carbon-100% Power
Join Date: Apr 2004
Location: Thessaloniki,GREECE
Posts: 1,706
Likes: 0
Received 0 Likes
on
0 Posts
Well i need some help now...Again :D
1.Has Anyone used canzoomer canscan to take numbers from the car??In what numbers(stoichiometry) are you running??11?12??
2.If anyone has the profec e0-1,where do you connect the pressure sensor?In the emanage or in the e0-1???
3.And how many modules has the emanage??2 or 3??
1.Has Anyone used canzoomer canscan to take numbers from the car??In what numbers(stoichiometry) are you running??11?12??
2.If anyone has the profec e0-1,where do you connect the pressure sensor?In the emanage or in the e0-1???
3.And how many modules has the emanage??2 or 3??
#285
Registered
Join Date: Aug 2004
Location: Virginia/Maryland
Posts: 1,294
Likes: 0
Received 0 Likes
on
0 Posts
I changed the Gapping on my spark plugs this weekend from stock 0.48 to .30 as suggested by greddy. It definitely made a difference. I think the car runs much better. Although the turbo doesn't come on as strong as before, overall it does feel more powerful. I would recommend this change.
#286
Registered User
Hey everyone, got my turbo installed (finally finished tonight, about thirty minutes ago), Car runs good, idles good, looks as though I need to adjust BOV some because when I rev and let off, it chokes some. But so far no big issues, want to take it on a test drive, but not without the boost gauge. I have defi BF, where does the vacuum hose from the sensor go? I can not figure it out, i searched but could not find it, thanks!
Chris
Chris
#287
Registered
Join Date: Aug 2004
Location: Virginia/Maryland
Posts: 1,294
Likes: 0
Received 0 Likes
on
0 Posts
It goes onto the other maintenance port on the intake manifold. There should be two of them, one of them you connected your wastegate control line to, hook up the boost gauge to the other one.
#288
90% Carbon-100% Power
Join Date: Apr 2004
Location: Thessaloniki,GREECE
Posts: 1,706
Likes: 0
Received 0 Likes
on
0 Posts
Hey guys what number do you get???i am very lean from 2-3 runs i made...i saw it with canscan...i hitted yesterday night with low temp arround 13 which is very bad...I have the midp-4 from canzoomer right now and the greddy sp2 on and that numbers with my turbo don't seem good...Do you believe the cat is the problem???Its a 5" size cat..The stock is 2"
#290
90% Carbon-100% Power
Join Date: Apr 2004
Location: Thessaloniki,GREECE
Posts: 1,706
Likes: 0
Received 0 Likes
on
0 Posts
Sh$t there is not a single man here who can tune this thing...We are left behind...Tune it you mean making a whole new map from 0!!?? this thing is definately very difficult for me...AND I LOVE MY CANZOOMER!!!
#291
Int-X 293WHP 242TQ :)
Join Date: Oct 2002
Location: Omaha, NE
Posts: 1,022
Likes: 0
Received 0 Likes
on
0 Posts
You don't start from scratch to tune -- you just adjust the emanage fuels maps. You will need to get the current map from GReddy (or better yet use MazdaManiac's current map) -- you can find these here on the board. The pre-loaded map is password locked but GReddy has released an unlocked version for tuning purposes. You will need a laptop, cable and the GReddy support tool.
#292
Ex- member.
Thread Starter
Also, you'll need someway of monitoring your Air/Fuel, the canscan is not adequate since you can't see anything below 12.0 (Greddy says the target AFR is 10.5-10.8).
Jeff is using the LM-1.
Jeff is using the LM-1.
#293
Registered User
Hey guys, finally did my test run. Car is fast but runs poor! Had backfires, figured I would cause i do hve high flow cat. But I have a cel, hooked up scansalyer and actually have three! P0300 - Random Misfire, P0172- System too Rich and Pending P0302 - Rear Rotor Misfire. So when I drive the car, it runs rough, jumps alot, not smooth at all. Is all this caused by the high flow cat? If not what should I do? Have not loaded Jeff's map yet, should I? also i think i have a leak, not holding boost good but I have the boost tester order for that. Anyone have any suggestion?
#294
Ex- member.
Thread Starter
Backfiring is normal. It'll still do it with the stock cat just won't be as loud.
Those CEL's are not good. Maybe call up Greddy and ask them, it could be a bad emanage map.
Double check all your connections, especially the emanage harness wires and the wires going to the black boxes. Do you have 2 or 3 black boxes? Greddy has an updated 3rd dongle that fixes 2 CEL, neither of which you have, yet (they pop up in warm weather).....
P0131 Front HO2S circuit low voltage ON 2 HO2S
P0410 AIR system problem ON 2 AIR system
First, check for leaks. Then, I'd put the stock cat back on, just to eliminate that as the problem.
Load either Greddy's latest map or Jeff's.
Do you have any shops in your area that do dyno tuning and are familiar with the emanage?
Did you replace or mess with the sparkplugs or sparkplug wires?
Those CEL's are not good. Maybe call up Greddy and ask them, it could be a bad emanage map.
Double check all your connections, especially the emanage harness wires and the wires going to the black boxes. Do you have 2 or 3 black boxes? Greddy has an updated 3rd dongle that fixes 2 CEL, neither of which you have, yet (they pop up in warm weather).....
P0131 Front HO2S circuit low voltage ON 2 HO2S
P0410 AIR system problem ON 2 AIR system
First, check for leaks. Then, I'd put the stock cat back on, just to eliminate that as the problem.
Load either Greddy's latest map or Jeff's.
Do you have any shops in your area that do dyno tuning and are familiar with the emanage?
Did you replace or mess with the sparkplugs or sparkplug wires?
#295
Registered User
hey andrian, thanks for getting back to me. I went ahead and installed the stock cat, that took care of most of the problems. got a cel tonight, have not had time to check to see what it is, i think i will load jeff's map tomorrow cause the car is terrible on gas, a lot worse that it use to be! Rnning really rich, like 14.5 to 15 at some points. probably have fouled some spark plugs, should I go hotter or colder? I have the three boxes on the emange harness so i should be good there, checked with greddy to see if I needed an update and they said no. I pretty much have a boost leak, doesn't hold much more than three psi and hardly ever goes to five. I ordered the boost leak tester that was in the DIY (i think yours).
So all in all, its getting better, I have a friend who built rx 7s and we are going to tune it on sunday to get rid of the richness a little if Jeffs map doesnot take care of it. But i should have the latest greddy map might just be bad, I dunno.
Any other suggestions, or does everything sound like it is improving for me from your experience?
Thanks and happy to be boosted!
Chris
So all in all, its getting better, I have a friend who built rx 7s and we are going to tune it on sunday to get rid of the richness a little if Jeffs map doesnot take care of it. But i should have the latest greddy map might just be bad, I dunno.
Any other suggestions, or does everything sound like it is improving for me from your experience?
Thanks and happy to be boosted!
Chris
#296
Registered User
Join Date: Jan 2003
Location: SF Bay Area
Posts: 1,286
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by zoomzoom_8
the car is terrible on gas, a lot worse that it use to be! Rnning really rich, like 14.5 to 15 at some points.
________
ROLL BLUNTS
Last edited by PUR NRG; 05-01-2011 at 06:26 AM.
#300
Registered User
Originally Posted by PUR NRG
The reason they call it an Air Fuel Mixture is because the ratio is expressed as units of air to units of fuel. 15:1 is really lean, not really rich.
1. What is the average a/f on Jeffs map?
2. why was i running so lean on the stock map?
3. Why has the a/f got richer but better on gas?
Thanks guys
Chris