Coil Dwell Settings with ProTuner & AccessPort
#278
rev it up
I am purchaseing BHR coils. My supercharged car was tuned on factory coils without any increase in dwell settings.
I assume I should be able to do a direct swap and run the car without any issues?
I will look at getting a new tune done in the near future.
I assume I should be able to do a direct swap and run the car without any issues?
I will look at getting a new tune done in the near future.
#285
rev it up
So my instructions to the tuner is to increase the dwell times to 5ms. Can the tuner use the dwell table posted on page 9 by shelldude or do I have to specify specific targets for the various rev ranges?
#287
rev it up
#288
rev it up
#290
rev it up
Thanks for your help. Is there information somewhere on the dwell settings on the standard BHR kit. I have emailed Charles for this information. I assume the tuners may need the base settings?
#292
No respecter of malarkey
iTrader: (25)
it would be more accurate to say that most of them know nothing more than what they were told
direct your tuner to post 108 in this thread and to download the attached spreadsheet and use it per that post
watch this thread, in particular the RH area of the scope to view output relative to the different dwell settings as he changes them. From 5000 up the OE dwell setting is below 3.0 mS. What you don't have is the OE coil output relative to dwell for comparison. If you did then you'd understand why I'm recommending not to do it that way.
direct your tuner to post 108 in this thread and to download the attached spreadsheet and use it per that post
watch this thread, in particular the RH area of the scope to view output relative to the different dwell settings as he changes them. From 5000 up the OE dwell setting is below 3.0 mS. What you don't have is the OE coil output relative to dwell for comparison. If you did then you'd understand why I'm recommending not to do it that way.
#293
rev it up
Thanks Team, I found that post downloaded the spreadsheet and sent it off to the tuners.
I assume they will be able to access the required table using the HKS Fcon software and adjust accordingly.
I assume they will be able to access the required table using the HKS Fcon software and adjust accordingly.
#294
For those that still don't get it... I'll spell it out for you.
D585 Dwell (LS2 Truck) coils w/ heatsinks in ATR (thanks to Oltman):
D585 Dwell (LS2 Truck) coils w/ heatsinks in ATR (thanks to Oltman):
Code:
1000 2000 3000 4000 5000 6000 7000 8000 9000 6.50 5398 4116 3159 2821 2304 1792 1421 1152 896 7.75 3939 3229 2579 2312 2049 1792 1421 1152 896 9 2488 2342 1999 1802 1613 1613 1421 1152 896 10.25 1923 1850 1678 1567 1421 1421 1245 1152 896 11.5 1462 1462 1445 1383 1281 1281 1068 982 896 12.75 1211 1211 1211 1198 1141 1141 973 934 895 14 1065 1065 1065 1065 1053 1053 896 858 820 15.25 981 981 981 981 975 975 845 795 744.96 16.5 896 896 896 896 891 891 748 709 669
I have LS2 D514a coils, until now I have used a overall multiplier of 1.666 to get from 3ms dwell to 5ms dwell.
Should I be worried about the current draw when using overall 1.666 mulitplier with these coils?
Is this table above for D585 okey to use with LS2 D514a coils or should I just keep my table as it is.
Last edited by al3k87; 07-17-2014 at 07:33 AM. Reason: corrected multiplier value
#295
Bump...again
Hi all,
Has anyone had success in adjusting the dwell setting for D514 coils in ME? Im in the same situation as al3k87, and wondering the best way to go about doing it
Any help appreciated!
Has anyone had success in adjusting the dwell setting for D514 coils in ME? Im in the same situation as al3k87, and wondering the best way to go about doing it
Any help appreciated!
#296
Registered
The 514 coils seem to work with the stock dwell.
#297
Thanks for the reply Rote8. They do seem to work okay with stock dwell settings, but Im really wanting to optimise their performance if I can. Iv asked RaceRoots what they recommend but haven't heard anything back.
I have no idea what burning coils smell like - but I can imagine I wont like it! Does anyone have the base dwell figure for the D514 coils?
I have no idea what burning coils smell like - but I can imagine I wont like it! Does anyone have the base dwell figure for the D514 coils?
#298
Hi all,
I'm interested in buying the SakeBomb kit with the IGN1A/AEM coils.
As I far as I understood, they have a base dwell of 3ms. In this thread it says that stock are 3ms too and further it says they are 3,5ms. i didn't find the info elsewhere.
So my question is simple, do I have to adjust my dwell table if I go from OEM coils to those coils?
Excuse me if my english is not perfect, I'm French
I'm interested in buying the SakeBomb kit with the IGN1A/AEM coils.
As I far as I understood, they have a base dwell of 3ms. In this thread it says that stock are 3ms too and further it says they are 3,5ms. i didn't find the info elsewhere.
So my question is simple, do I have to adjust my dwell table if I go from OEM coils to those coils?
Excuse me if my english is not perfect, I'm French