Kinky_Kelsey

btw, decided to sell the nitrous kit to save up for an accessport and custom tune. Kit works fine, pm me if interested.

http://www.ksl.com/index.php?nid=218...search=nitrous

Kinky_Kelsey

Greddy Exhaust clip...

Sorry about the horrible quality, this was a video off my phone

http://www.youtube.com/watch?v=0f0x0h_1ShM

Kinky_Kelsey

and one of the AEM short ram intake I put on yesterday...

http://www.youtube.com/watch?v=jWdRhVGRuZA

8upbad

iTrader: (3)

^^ sounds great. Sounds really deep.

Kinky_Kelsey

Thanks, I'm really liking the sound so far

9krpmrx8

iTrader: (46)

Did you use a AEM CAI to make the Short Ram? Sounds good but sucking in Hot engine bay air is not good for performance.

Kinky_Kelsey

I bought the intake piping used locally, he claimed it was AEM and it was already short ram. Besides, in utah low mount CAI's usually get a lot of water in them from rain/snow. Though, I plan on building a heat shield to keep the air a little cooler around the intake filter

Kinky_Kelsey

Tein s-tech's came today though

Kinky_Kelsey

changed my mind, it got worse and worse every time i drove. So i took out the short ram and modded the stock intake box. I removed the two walls, and both the screens, then gently cleaned the MAF. I read up on the stock intake mod and I didn't see anyone who had tried removing the two screens, so i just went for it. performance wise it's much much better than the short ram, and feels better TQ wise compared to stock.

Kinky_Kelsey

another quick clip of how the modded box sounds, surpirsingly very similar to the short ram but not as annoying and better performing :D

http://www.youtube.com/watch?v=DK4kGpvOFW4

Kinky_Kelsey

Drop done! I love the ride of the S-Tech's, they are way good on cornering, and made it look more aggressive.

it was hard to capture the actual difference in ride height, but here's the pic's I've got so far...








All done







This is the how to thread I used, very helpful.

http://www.hi-impact.org/ryang/modif...ock_front.html

http://www.hi-impact.org/ryang/modif...hock_rear.html

shadycrew31

iTrader: (6)

The car will not lower until you preload the front springs.

jack the bottom of the assembly the knuckle under the brake rotor to its highest position. loosen the bolts holding the upper control arm. Now lower the assembly. raise the assembly back up to its highest position. now tighten the bolts back up to 53 ft lbs of tq (I think thats correct, look int he FSM). when you lower the assembly the bushings should be twisted kind of.

But the tire on and give it a few days to settle.

Kinky_Kelsey

not sure I understand what you mean by all of that

RX8SHNKVI

iTrader: (1)

Subscribed...

Kinky_Kelsey

Sorry all, nothing new yet. I've been barely scraping by on cash flow.

Expect some agency power Endlinks and BHR Ignition Coils here soon :D

Kinky_Kelsey

winter cleaning, ran a can of seafoam with good results. Kelsey seems to be running smoother, wish i would have grabbed a video of the smoke show.

Kinky_Kelsey

Just looking through my pictures and thought it was cool to see the difference in the past year...

TRIGG3R12

Hey kinky kelsey, the first thing i decided i wanted to do to my RX-8 when i got it was to put a sub inbetween the back seats, i was thinking of building a custom box for it, but the one you have is EXACTLY what i want, can you point me in the direction of where you got it or did you build it?

SayNoToPistons

iTrader: (8)

I would put on the screen closest to the MAF. It is there to even out the air flow for the MAF and of course to provide some protection from large particles.