water/methanol injection
Just gotta get that balance right.
With a decent intercooler and efficient turbo, you really don't need a TON of water.
That is what I'm using. Works great.
Thread Starter
Registered
Joined: Jan 2007
Posts: 1,401
Likes: 0
From: NJ
[QUOTE=MazdaManiac;2855160]I'm running the even-more-powerful LS2 setup and it will still misfire with too much water.
Just gotta get that balance right.
With a decent intercooler and efficient turbo, you really don't need a TON of water.
good thing to know....i will really consider the balance....thank you jeff
steven
Just gotta get that balance right.
With a decent intercooler and efficient turbo, you really don't need a TON of water.
good thing to know....i will really consider the balance....thank you jeff
steven
BDC Motorsports
Joined: Nov 2006
Posts: 417
Likes: 1
From: Dallas, Tx
Registered
Joined: Oct 2007
Posts: 1,574
Likes: 2
From: Boosted...
Registered User
Joined: Jan 2009
Posts: 5
Likes: 0
both of them parts are standard in the pump on used with the kits. Yes you can run run straight m1. But we recommend no more than a 50/50 mix. We don't recomend any top end lubes in the pump. Meth is not going to hurt the pump if it has the right valves and seals. And you are not injecting enough to worry about cylinder wash so i would not use it. FWI there are other brands of Methanol out there that are cheaper.
Last edited by DevilsOwn; Feb 10, 2009 at 08:32 AM.
exactly---i advise strongly agaisnt chasing power with a water meth system in this way. I advise only using it for damn good insurance for us boosted folks. If you want more power then suck it up and tune for it---dont start adding things to the fluid being injected---all kinds of reasons---remember also we have a 2 valve tuned intake(most of us have d/ced the vdi) and if you are injecting stuff above those ports---well --when those ports open there MAY have been some accumulation? That could =NOT GOOD if OTHER stuff is in the fluid.
OD
OD
Thread Starter
Registered
Joined: Jan 2007
Posts: 1,401
Likes: 0
From: NJ
exactly---i advise strongly agaisnt chasing power with a water meth system in this way. I advise only using it for damn good insurance for us boosted folks. If you want more power then suck it up and tune for it---dont start adding things to the fluid being injected---all kinds of reasons---remember also we have a 2 valve tuned intake(most of us have d/ced the vdi) and if you are injecting stuff above those ports---well --when those ports open there MAY have been some accumulation? That could =NOT GOOD if OTHER stuff is in the fluid.
OD
OD
it's a matter of buying it, and dyno it to find out ...steven
Yeay Boosted!
Joined: Oct 2007
Posts: 271
Likes: 0
From: New Hampshire
I'm getting one of these kits.. I have a few question, where are people putting their nozzle? are people using multiple nozzles? what size nozzles are people using? 150cc?
anyone have a picture of one installed?
I was thinking of putting a nozzle in the UIM at the top in the plastic, at an angle since I have to take it off anyways to put on a greddy backing plate...
thanks a bunch.
anyone have a picture of one installed?
I was thinking of putting a nozzle in the UIM at the top in the plastic, at an angle since I have to take it off anyways to put on a greddy backing plate...
thanks a bunch.
I pulled off my UIM yesterday and after about 400 or so miles of water/meth spray the inside of my UIM is completely clean. And from what I can see the LIM is very clean inside as well- good news.
It was odd, tho, on the inside of my throttle body there was some sort of dry powder that had accumulated- had a very light green coloring to it. Not too much there, I whipped it away with a rag, but it was odd.
It was odd, tho, on the inside of my throttle body there was some sort of dry powder that had accumulated- had a very light green coloring to it. Not too much there, I whipped it away with a rag, but it was odd.
Thread Starter
Registered
Joined: Jan 2007
Posts: 1,401
Likes: 0
From: NJ
I pulled off my UIM yesterday and after about 400 or so miles of water/meth spray the inside of my UIM is completely clean. And from what I can see the LIM is very clean inside as well- good news.
It was odd, tho, on the inside of my throttle body there was some sort of dry powder that had accumulated- had a very light green coloring to it. Not too much there, I whipped it away with a rag, but it was odd.
It was odd, tho, on the inside of my throttle body there was some sort of dry powder that had accumulated- had a very light green coloring to it. Not too much there, I whipped it away with a rag, but it was odd.
steven
Thread Starter
Registered
Joined: Jan 2007
Posts: 1,401
Likes: 0
From: NJ
I'm getting one of these kits.. I have a few question, where are people putting their nozzle? are people using multiple nozzles? what size nozzles are people using? 150cc?
anyone have a picture of one installed?
I was thinking of putting a nozzle in the UIM at the top in the plastic, at an angle since I have to take it off anyways to put on a greddy backing plate...
thanks a bunch.
anyone have a picture of one installed?
I was thinking of putting a nozzle in the UIM at the top in the plastic, at an angle since I have to take it off anyways to put on a greddy backing plate...
thanks a bunch.
steven
Registered
Joined: Apr 2003
Posts: 9,134
Likes: 26
From: Houston
A few days ago I "steam cleaned" the inside of my engine by sucking a gallon of water into the manifold through a vacuum line and holding the engine at 2K rpm! Does that count as aux injection? BTW the engine runs smoooooth now!
For those who haven't followed Brian's thread on the 7club forum, he broke the rear engine housing around the dowel pin.
For those who haven't followed Brian's thread on the 7club forum, he broke the rear engine housing around the dowel pin.