The Official Overboosted Overlords Club
Do you have check valves in the Jet air and OMP air supply lines? If not you just pressurized your "crankcase" and blew out one of the vent lines...and a lot of oil all over the place
Last edited by dannobre; Jan 4, 2009 at 09:36 PM. Reason: spelling :)
Well that explains it, thanks alot. Can these be acquired @ my local hardware store.
Also what connector did I blow and will it need to be replaced now?
Also what connector did I blow and will it need to be replaced now?
Last edited by Derex'8; Jan 4, 2009 at 07:20 PM.
Send me the data I need, in the format I need it in and I can set you up with whatever it is you need.
Dongbag extrordinare
Joined: Nov 2004
Posts: 1,090
Likes: 0
From: Away from the fruits of my labor
-Yambo
OK I sprayed!!! ZEX #82021 kit with BHR spacer. I am going to stick to 55-shot for the time being.. 65-shot forthcoming!! Here is my build thread with pics of the entireeee build and install. https://www.rx8club.com/series-i-major-horsepower-upgrades-93/als-nitrous-install-thread-163452/
mork you using the same belt?
How do you get added to the list--what mods need to be mentioned?
Temps are a non issue anymore for me air/coolant/oil all well controlled.
In case some dont know
pettit kit c flash
snow dual nozzle w/m trunk mount kit.
yukon coils-self made plug and play
secondary radiator
relocated oil and fuel filters(thats right
many more mods where do ya stop?
olddragger
How do you get added to the list--what mods need to be mentioned?
Temps are a non issue anymore for me air/coolant/oil all well controlled.
In case some dont know
pettit kit c flash
snow dual nozzle w/m trunk mount kit.
yukon coils-self made plug and play
secondary radiator
relocated oil and fuel filters(thats right
many more mods where do ya stop?
olddragger
had the connectors left over from the mazsport ignition
one of those coils went bad and I saw the light.
I dont have a build thread dont even know how to do one?
But here is my mods--the previously stated ones
+
act lighted flywheel, eddy street clutch /plate
upgraded water pump and custom 180 degree barrel type thermostat(use it during very hot summer days)
rerouted heater hoses to under the car (does help cooling a little and keeps heat away from the intake)
custom fabbed intake--i cut the front support beam to ski slope air to the aem filter i have---cai that works very well
custom aluminum a/w tank --upgraded a/w cooler and pump
pettit bypass valve
deleted vdi and jet air
custom worked LIM
header shielded
air pump delete
secondary radiator (the 1st one to do this--meh)
mazmart oil pressure regulator mod
filter mag
ls2 coil pack with custom wires and mazsport ignition solution mount
oil cooler thermostat mod
custom cannister wwf fluid bottle
oil filter relocation to passenger firewall with custom mount and ss hoses
snow dual nozzle water meth system with trunk mount pump tank
mazsport dual resonated midpipe and rb cat back
custom gauges --lotek pod and custom RB ashtray monitoring coolant/oil temps, intake charge temps (at upper/lower intake junction) and a innovate a/f gauge. boost vac, oil pressure
09 transmission with syncro saver
k/w varient coil overs, rb bars and endlinks
enkei rpf 18/8 for street with yokohama s drive tires
enkei rpf's 18x9.5 with the 245 R6's for track.
carbotecj xp 8 pads in fron(track) and back
upgraded brake fluid of coarse
some fender wheel chad mod to help a little with brake cooling_
front rotor symbol removed(increase air flow--dont laugh)
o9 fuel pump mods
efi dude monitoring.
4th brakelight in rear rotary symbol
prob some other stuff I have forgotten about!
OD
https://www.rx8club.com/attachment.p...1&d=1237426666
one of those coils went bad and I saw the light.I dont have a build thread dont even know how to do one?
But here is my mods--the previously stated ones
+
act lighted flywheel, eddy street clutch /plate
upgraded water pump and custom 180 degree barrel type thermostat(use it during very hot summer days)
rerouted heater hoses to under the car (does help cooling a little and keeps heat away from the intake)
custom fabbed intake--i cut the front support beam to ski slope air to the aem filter i have---cai that works very well
custom aluminum a/w tank --upgraded a/w cooler and pump
pettit bypass valve
deleted vdi and jet air
custom worked LIM
header shielded
air pump delete
secondary radiator (the 1st one to do this--meh)
mazmart oil pressure regulator mod
filter mag
ls2 coil pack with custom wires and mazsport ignition solution mount
oil cooler thermostat mod
custom cannister wwf fluid bottle
oil filter relocation to passenger firewall with custom mount and ss hoses
snow dual nozzle water meth system with trunk mount pump tank
mazsport dual resonated midpipe and rb cat back
custom gauges --lotek pod and custom RB ashtray monitoring coolant/oil temps, intake charge temps (at upper/lower intake junction) and a innovate a/f gauge. boost vac, oil pressure
09 transmission with syncro saver
k/w varient coil overs, rb bars and endlinks
enkei rpf 18/8 for street with yokohama s drive tires
enkei rpf's 18x9.5 with the 245 R6's for track.
carbotecj xp 8 pads in fron(track) and back
upgraded brake fluid of coarse
some fender wheel chad mod to help a little with brake cooling_
front rotor symbol removed(increase air flow--dont laugh)
o9 fuel pump mods
efi dude monitoring.
4th brakelight in rear rotary symbol
prob some other stuff I have forgotten about!
OD
https://www.rx8club.com/attachment.p...1&d=1237426666
Last edited by olddragger; Jan 29, 2011 at 08:00 AM.
Lol same here--family thinks I am crazy. Made my Mount for the coils(remember on the pettit they are mounted up front) out of a thrown away weight bench.
My little place is starting to look like Fred Sanford's.
OD
My little place is starting to look like Fred Sanford's.
OD
He's already got theme music, you can't change it once it's been designated.
http://www.youtube.com/watch?v=u9sTxEuuyVU
http://www.youtube.com/watch?v=u9sTxEuuyVU
YES! I feel you - I even have a car on blocks... and now a new engine in the back of a friends pick-up.
