Will It Fit Thread
#7452
I am THAT guy
iTrader: (1)
18x8 +5 with 225/45/18 on stock height
NOT asking if it will look good but im asking if it will rub in the front when the steering wheel is turned all the way one way ??
Once again not asking whether if it will look good cause this set up is just to fool around... ill remove it depending on how it looks.
Thanks
NOT asking if it will look good but im asking if it will rub in the front when the steering wheel is turned all the way one way ??
Once again not asking whether if it will look good cause this set up is just to fool around... ill remove it depending on how it looks.
Thanks
#7454
Girls who drive stick FTW
iTrader: (1)
Just finished installing. The wheels are 18x8 +30 with 25mm spacers. Rear looks really good but the front is pretty poke as i expected. I might remove the spacers in the front.
Question for you guys. I am rubbing in the wheel well when i turn in the front. Can i just leave it and after a while the tire will just shave off a bit of the wheel well ??? Have you guys had that problem ?
Thanks
Question for you guys. I am rubbing in the wheel well when i turn in the front. Can i just leave it and after a while the tire will just shave off a bit of the wheel well ??? Have you guys had that problem ?
Thanks
#7457
Girls who drive stick FTW
iTrader: (1)
^ To be honest it looks like **** in the front but the rear looks good.
I turned my wheel all the way one way and it looks like its just skimming the wheel well. I hope i should be okay rolling on these for one day. Cause im putting my stock wheels back on tomorrow. This was just to see what it would look like. lol
I turned my wheel all the way one way and it looks like its just skimming the wheel well. I hope i should be okay rolling on these for one day. Cause im putting my stock wheels back on tomorrow. This was just to see what it would look like. lol
#7466
maybe, but yes i was. But if you are correct the how does an inch and 3mm make THAT much of a difference....thought it was the offset of the bolt pattern to the edge or the rim and the width of the outside rim is the total?
Last edited by Daeity; 09-20-2011 at 06:20 PM.
#7468
okay, i want these xxr 526's really bad!
SPECS: front=18x9.0 offset +25
rear=18x10.5 offset +20
---WITH 225/45/18 tires. im not lowered right now. How much will it poke out in front and rear? Will this even fit? thanks
SPECS: front=18x9.0 offset +25
rear=18x10.5 offset +20
---WITH 225/45/18 tires. im not lowered right now. How much will it poke out in front and rear? Will this even fit? thanks
#7470
**Does the offset refer to the concaveness**
**Does the offset refer to the amount of mm that the center hub is "offset" from the center of th....i dont even care anymore. I tried to put it in words but **** it! Ill but my MR116s
#7472
Tie-Fighter
iTrader: (1)
Join Date: Jun 2010
Location: Merritt Island, FL
Posts: 68
Likes: 0
Received 0 Likes
on
0 Posts
Fitment noobie <--
I'm looking at some Wedssport SA60M's 18x10 +35 with 295/30/18's all around.
Sitting on Tokico D-Specs and Mazdaspeed springs (Will move to KW V3's later, which I know would be the ideal set up).
Roll Rear AND Front, check, but will it fit?!!??
Thanks
I'm looking at some Wedssport SA60M's 18x10 +35 with 295/30/18's all around.
Sitting on Tokico D-Specs and Mazdaspeed springs (Will move to KW V3's later, which I know would be the ideal set up).
Roll Rear AND Front, check, but will it fit?!!??
Thanks
#7474
OMGITM!
iTrader: (15)
Join Date: Jan 2006
Location: Sunny Southern California
Posts: 3,513
Likes: 0
Received 6 Likes
on
6 Posts
Did we ever determine the highest offset + widest width wheels that have been run on the rx8? i.e. the wheels with the least inner clearance?
I recall discussing it before and bringing up the 10.5 ET43's that TeamRX8 ran, then sold, but has there been anything else with confirmed less inner clearance?
I recall discussing it before and bringing up the 10.5 ET43's that TeamRX8 ran, then sold, but has there been anything else with confirmed less inner clearance?