Anyone here run Bilstein PSS9's?
#501
hi guys after reading this forum for 20 pages. im planing to also buy thiscoilover for my r3. i just want to ask anyone knows how low u could drop bilstein if i could slam it down? and being my car an s2 r3 is there any difference on what shoul i take from my oem bilstein shocks? pls can som1 help me.... thank you
#502
Water Foul
^ These coilovers will go very low on a Series 2 car, however you will absolutely ruin the car's handling properties by slamming it. Mazda designed the car to run at the factory ride height. Some handling improvements may arguably be had in some areas by lowering the car about 1 inch, but beyond that, you are trading performance for aesthetics, and that is a very poor trade in my opinion.
Moving from the R3 suspension to PSS9s will result in a much stiffer ride. My car is just on the edge of tolerable on the street--even with the dampers set to full soft. If you are not tracking the car or AutoXing, there are much cheaper and more comfortable ways to slam the car if that is your thing.
When I installed my PSS9s, I set them to the maximum recommended height according to the instructions. About one month later, I dropped the front 0.25 inches more, then had the car corner balanced and aligned for the track. The net result is a ride height of ~13.5 inches all the way around, and I would not want it any lower.
Moving from the R3 suspension to PSS9s will result in a much stiffer ride. My car is just on the edge of tolerable on the street--even with the dampers set to full soft. If you are not tracking the car or AutoXing, there are much cheaper and more comfortable ways to slam the car if that is your thing.
When I installed my PSS9s, I set them to the maximum recommended height according to the instructions. About one month later, I dropped the front 0.25 inches more, then had the car corner balanced and aligned for the track. The net result is a ride height of ~13.5 inches all the way around, and I would not want it any lower.
Last edited by Steve Dallas; 05-12-2014 at 11:05 PM.
#503
Registered
iTrader: (6)
Join Date: Mar 2005
Location: Baltimore, MD
Posts: 663
Likes: 0
Received 0 Likes
on
0 Posts
Just re-visiting this once again before I order parts. I think I have the rears covered, but in the pic below showing what's needed for the fronts, there are 2 black parts shown. The top one I believe is #10 on the diagram (bushing), but the other piece didn't appear to be mentioned in the replies as a re-used part. Can someone please clarify? Is the metal spacer (15) also re-used?
Thanks again guys.
Thanks again guys.
Bumping this thread for some install info! Can someone please clarify which pieces I'd need from the stock setup to install the Bilsteins? I may sell my old assemblies as a whole and I don't want to swap any parts over. Plus these parts are not expensive and it'd be nice to have nice shiny new ones after 9 years, anyway. Certain pieces like the upper strut mount and gasket are obvious but I'm not 100% about some of the bushings and other parts.
Here are the front and rear parts diagrams for reference:
Front:
Rear:
Thanks in advance.
Here are the front and rear parts diagrams for reference:
Front:
Rear:
Thanks in advance.
#505
Registered
iTrader: (6)
Join Date: Mar 2005
Location: Baltimore, MD
Posts: 663
Likes: 0
Received 0 Likes
on
0 Posts
Okay guys, I've had the PSS9's for a while now, but haven't been able to install them because the car's at the shop. Hopefully next week I'll get them on.
Anyway I was adding in the OEM parts to the front assemblies and I was a little unsure about the double locking nuts that come with the Bilsteins. The instructions aren't specific and the diagram I believe only shows one nut. Where do these two nuts go in the order of assembly? I only remember there being one in the OEM setup.
Thanks...
Anyway I was adding in the OEM parts to the front assemblies and I was a little unsure about the double locking nuts that come with the Bilsteins. The instructions aren't specific and the diagram I believe only shows one nut. Where do these two nuts go in the order of assembly? I only remember there being one in the OEM setup.
Thanks...
Thread
Thread Starter
Forum
Replies
Last Post
JimmyBlack
Series I Major Horsepower Upgrades
273
02-10-2020 10:23 PM