Won't rev past 6500
#1
Registered User
Thread Starter
Join Date: May 2006
Location: Phoenix, AZ
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Won't rev past 6500
The last 2 weeks when I start the car in the morning ( about 4:30 am, 50 degrees outside ) the car immediately revs up to about 3500 and sits there for about 10 seconds before coming down to 2000 or so. It has never done that before?
The last 2 mornings when I go to leave and pull out on to the street the car won't rev past 6500 rpms in 1st gear and feels as though it is hitting the rev limiter? After shifting to 2nd, it'll rev up just fine all the way up to 9k. It just happened again this afternoon when I left for lunch ( the car's been sitting since 5 this morning and it was 1 pm when I left ). Any ideas? Thanks.
The last 2 mornings when I go to leave and pull out on to the street the car won't rev past 6500 rpms in 1st gear and feels as though it is hitting the rev limiter? After shifting to 2nd, it'll rev up just fine all the way up to 9k. It just happened again this afternoon when I left for lunch ( the car's been sitting since 5 this morning and it was 1 pm when I left ). Any ideas? Thanks.
#3
Registered User
Join Date: Apr 2006
Location: Tigard, OR
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
I've been having a similar problem - kinda of putters out at exactly 5500 rpm and only the first time (sometimes the second) time accelerating. After that it's fine. It started happening just recently - so I figured it was the cold weather setting in as well - I'll need to try letting it warm up a bit and see if that helps.
#4
Administrator
iTrader: (7)
danno is correct: the ECU won't let you rev really high when the engine is cold. It's not very good for your engine so the ECU doesn't let you do it.
#5
Registered
If the car is still not up to full operating temp, do not try to take it up high or get on it very hard. Mazda has a failsafe to help prevent this. by holding you below a certain spot until it is warmed up.
Now to scare you...
Since the engine is made from alternating metals with the rotor housings being aluminum, this means that each metal does not expand or contract at the same rate. With normal warmup this isn't an issue. It's sudden heating that can really affect it though, specifically the aluminum rotor housings. Remember that the internal chamber temps can hit 2000*F at full throttle but due to the water jackets the actual housings may get up to about 400*F or so. If you get on it really hard and pass all of this heat out the bottom of the engine, but the top of the engine is still only at 100*F or so, that's a severe expansion difference in the housings itself. Aluminum flanges warp easily when welding due to severe heating so they must be done slowly to avoid this. Same thing here. Warm it up slowly. You don't want to replace an engine that blew a coolant seal from warping.
Now to scare you...
Since the engine is made from alternating metals with the rotor housings being aluminum, this means that each metal does not expand or contract at the same rate. With normal warmup this isn't an issue. It's sudden heating that can really affect it though, specifically the aluminum rotor housings. Remember that the internal chamber temps can hit 2000*F at full throttle but due to the water jackets the actual housings may get up to about 400*F or so. If you get on it really hard and pass all of this heat out the bottom of the engine, but the top of the engine is still only at 100*F or so, that's a severe expansion difference in the housings itself. Aluminum flanges warp easily when welding due to severe heating so they must be done slowly to avoid this. Same thing here. Warm it up slowly. You don't want to replace an engine that blew a coolant seal from warping.
#7
Registered
Join Date: May 2006
Location: Milan, Michigan
Posts: 575
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by rotarygod
If the car is still not up to full operating temp, do not try to take it up high or get on it very hard. Mazda has a failsafe to help prevent this. by holding you below a certain spot until it is warmed up.
Now to scare you...
Since the engine is made from alternating metals with the rotor housings being aluminum, this means that each metal does not expand or contract at the same rate. With normal warmup this isn't an issue. It's sudden heating that can really affect it though, specifically the aluminum rotor housings. Remember that the internal chamber temps can hit 2000*F at full throttle but due to the water jackets the actual housings may get up to about 400*F or so. If you get on it really hard and pass all of this heat out the bottom of the engine, but the top of the engine is still only at 100*F or so, that's a severe expansion difference in the housings itself. Aluminum flanges warp easily when welding due to severe heating so they must be done slowly to avoid this. Same thing here. Warm it up slowly. You don't want to replace an engine that blew a coolant seal from warping.
Now to scare you...
Since the engine is made from alternating metals with the rotor housings being aluminum, this means that each metal does not expand or contract at the same rate. With normal warmup this isn't an issue. It's sudden heating that can really affect it though, specifically the aluminum rotor housings. Remember that the internal chamber temps can hit 2000*F at full throttle but due to the water jackets the actual housings may get up to about 400*F or so. If you get on it really hard and pass all of this heat out the bottom of the engine, but the top of the engine is still only at 100*F or so, that's a severe expansion difference in the housings itself. Aluminum flanges warp easily when welding due to severe heating so they must be done slowly to avoid this. Same thing here. Warm it up slowly. You don't want to replace an engine that blew a coolant seal from warping.
If it doesn't prevent it, then I think maybe rev-limit at lower RPM's or Mazda should think of a fix. After all, this car was intended to be sold to the expert drivers that will race with it at the track as well as the every-day commuter. Therefore, not everybody will wait until the car warms up.
#8
Registered User
Originally Posted by puch96
Can you get warping even though Mazda tries to prevent this by rev-limiting?
If it doesn't prevent it, then I think maybe rev-limit at lower RPM's or Mazda should think of a fix. After all, this car was intended to be sold to the expert drivers that will race with it at the track as well as the every-day commuter. Therefore, not everybody will wait until the car warms up.
If it doesn't prevent it, then I think maybe rev-limit at lower RPM's or Mazda should think of a fix. After all, this car was intended to be sold to the expert drivers that will race with it at the track as well as the every-day commuter. Therefore, not everybody will wait until the car warms up.
#10
the stig is my hero
Join Date: Feb 2006
Location: NC
Posts: 701
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by puch96
Can you get warping even though Mazda tries to prevent this by rev-limiting?
If it doesn't prevent it, then I think maybe rev-limit at lower RPM's or Mazda should think of a fix. After all, this car was intended to be sold to the expert drivers that will race with it at the track as well as the every-day commuter. Therefore, not everybody will wait until the car warms up.
If it doesn't prevent it, then I think maybe rev-limit at lower RPM's or Mazda should think of a fix. After all, this car was intended to be sold to the expert drivers that will race with it at the track as well as the every-day commuter. Therefore, not everybody will wait until the car warms up.
Bottom line: give your car a few minutes to warm up before revving the crap out of it.
#11
The Professor
Originally Posted by puch96
Can you get warping even though Mazda tries to prevent this by rev-limiting?
If it doesn't prevent it, then I think maybe rev-limit at lower RPM's or Mazda should think of a fix. After all, this car was intended to be sold to the expert drivers that will race with it at the track as well as the every-day commuter. Therefore, not everybody will wait until the car warms up.
If it doesn't prevent it, then I think maybe rev-limit at lower RPM's or Mazda should think of a fix. After all, this car was intended to be sold to the expert drivers that will race with it at the track as well as the every-day commuter. Therefore, not everybody will wait until the car warms up.
This car also drinks oil on a pretty regular basis.
#12
Registered
Join Date: May 2006
Location: Milan, Michigan
Posts: 575
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by staticlag
just to keep all everyone informed:
This car also drinks oil on a pretty regular basis.
This car also drinks oil on a pretty regular basis.
Thread
Thread Starter
Forum
Replies
Last Post
Shankapotamus3
Series I Trouble Shooting
28
03-14-2021 03:53 PM
tommy26Germany
Series I Trouble Shooting
11
09-29-2015 10:33 AM