200.mph

iTrader: (9)

9k covered that in his last post

Mr_Pieper

All of that stuff on the shelves laying on the ground + shady doing a gangster pose = SARX garage.

jayrerickson

Told you guys I was pulling the trans to clean it up and give it a paint job. Gives me more room to put a under body coat on too. And I get to clean and paint the PPF. Many good reasons to pull the trans. Even saw that the drive shaft bolts were fugly. Will be replacing those. Might even take the diff out to clean and paint.

Its not like this stuff is hard to pull. I did everything you see myself. There is one thing I learned and still use today "Be smarter then what your working on". This is just a big boy erector set. Just because you think I cant do it doesn't mean I cant.

Not mounting the motor to the stand until the rebuild. Then I will be mounting vertical in sections as it gets built. Its not like I'm the first that has ever done this or haven't **researched** on what to do.

You guys sound like I'm building a time machine. "Have fun mounting the flux capacitor", but then not say why. hahaha lol.

jayrerickson

All that stuff is garbage that the wife makes me keep with no where to put. So I pile it up in that one corner. Odd shaped stuff were it wont fit on the shelf's...

Shady doing a gangster pose, where? I want to see.

What does SARX mean? Cant be the definition of the word.

200.mph

iTrader: (9)

we covered what sarx means last week in another thread

jayrerickson

I'm searching for it.


I cant find it. Must not be a popular word or term.

Found it, had to search by post.

"San Antonio Rotary Xtremists"

200.mph

iTrader: (9)

we had much better answers last week.

9krpmrx8

iTrader: (46)

Sweet. Flux capacitors FTW.

Mr_Pieper

That's because they blow so many up, right?

shadycrew31

iTrader: (6)

This is all the help I will give you... Use it wisely.

Pineapple Racing - Tools & Equipment

Carbon8

iTrader: (4)

The amount if work needed to pull the tranns, not to mention ensuring the PPF is installed and "aligned" properly is not work a fresh paint job IMO.

Yes, since you just asked PPF alignment is important.

jayrerickson

Not removing the oil pan FAIL...

9krpmrx8

iTrader: (46)

You popped a hole in the pan? You didn't drain the engine oil before hand? Nice

jayrerickson

lol

No, didnt drain the trans. When I angled the motor and trans I put a pan under the trans to drain it from the input shaft.

Thought it was far enough away to continue to pull it out. It wasn't, trans hit the corner and oil everywhere.

Kinda happy I did it. Made me clean the floor with cat litter and then soap and water. Now I have a nice new looking floor to work on.

On a side note, I'm waiting to get a socket for the flywheel. What size is that thing? Looks like a 2" socket.

I didn't explain to much with the pictures and what I found.

Found a very lose spring in the clutch disc. You can spine it by hand. The throw out bearing is bad, you can hear the bearings inside grinding.

Broke 2 lower ac pump bolts. Both snapped and are sticking 1/4 inch out the housing. At least it gave me something to work with. Should be easy to get out.


All but 3 exhaust bolts striped. I had a bolt extractor and that worked perfect.

One of my front and rear trialling arm links are gone. So old they fell apart.

Other then that everything looks good.

What do you guys think about taking the AC out? Mine still works...

9krpmrx8

iTrader: (46)

Ah it was trans fluid. Looks dirty.

jayrerickson

Very dirty.

bose

iTrader: (5)

I wouldn't take out a working a/c, no air sucks *****. Unless it's a track only car, leave it be.

CRO8TIA

You pulled the engine and tranny without draining the trans or removing the gear stick-shifter ? Come on , fess up, this is your first engine R+R .

Carbon8

iTrader: (4)

Any progression? Or can we declare this thread dead.

jayrerickson

I have been very busy.

I got the crank pulley bolt off. Took a inch drive impact to do so.

Now I'm just debating to buy the flywheel socket or find one to use.

Took the engine to my buddy's shop, he rebuilds semi trailers. He didn't even have the right socket.

As soon as I get this socket, many more pics and progress will be done...

jayrerickson

What do you guys think about this socket?
Sunex 454M 3 4" Drive 6 Point Impact Socket 54mm | eBay

I think I'm just going to buy it. Should work and it is always good to have your own.

jayrerickson

A little more progress with out taking the flywheel nut off.

































Thought you guys would enjoy this too

Mod edit:
It was reported, so I think the answer is that we don't.

shadycrew31

iTrader: (6)

Don't need no stinking engine stand!


.....



:/....

TeamRX8

iTrader: (25)

We do need more pointless pics like used gaskets and such though, lots more ...

shadycrew31

iTrader: (6)

I hope we get close-ups of every seal...