the_duke313

could the haltech E8 be used with the mazsport kit?

rotarenvy

you should be able to configure them to work together for a 2 rotar engine. the haltechs are fairly flexible in how they can be configured but I would check the microtech manual for compatibility to see what it needs.

Mazurfer

No issues for me either(I'm NA as well), but I'm keeping a close eye on them.

kennyfrc1

iTrader: (6)

Okada Project FTW

tdiddy

My mazsport kit works well with my int x and the 3.5ms dwell. I have had the random misfire above 8000 rpm but it is in consistent and was greatly reduced by spacing my crank angle sensor out a little. I am still not sure about the ignitor.

with that said, i also have a set of OEM and a set of BHR coils that I will be able to compare and contrast when I am tuning this summer.

manolo

who knows about the Okada Projects Plasma Direct Ignition Coils at www.horsepowerfreaks.com

kennyfrc1

iTrader: (6)

I have them and would not trade anything for them.

Brettus

iTrader: (2)

/\ how about my avatar ?

AJ's Shinka

I wanted to get them (Okada) but they were a bit pricey. So I got the Mazsport coils and they work great.

DOMINION

Something about the Mazsport set up and Turboed 8's, they all seam to get random misfire above 8000 rpm

Race Roots

iTrader: (64)

Hmm... I don't.

kennyfrc1

iTrader: (6)

Glad they worked for you.

I lost power throughout the band with them on they dyno.

AJ's Shinka

Thanks I didn't see your hp and tq numbers in your sig before. Those are some nice numbers.

kennyfrc1

iTrader: (6)

and I still have a cat.

BDC

Yes.

For the other poster: Dwell time to 3.8ms.

They're Bosche transistor type coils from what I can tell.

B

halimsteven

so OBD, do you think we should set as 3.8 or 3.5, i don't think it's different that much right?
steven

BDC

.3ms of dwell time isn't terribly different but if those coils can be ran at 3.8 I'd run 'em at 3.8. I'm still not convinced they're adequate enough for higher loads but I could be wrong. I've only had experience with one set of them.

B

DOMINION

^Thanks for the info

AJ's Shinka

I'll be giving you a call my friend.

hackdss

how much do these coils go for do you ship to canada?

RWagz

You should have researched before posting. Mazsport is gone. Out of business. Defunct.

shaunv74

Welcome to the club. Check out the BHR ignition solution and PM Charles R. Hill for more info.

it's a complete kit that is well designed and an excellent upgrade over OEM.

Talic

i had the okada plasma coils on my procharged rx8, $750 later i melted 1 coil same day then the next day 2 more went when i had the dli2 on, no performance increase and no support or replacement coils. the hks dli2 was sent out for testing and came back fine, never burnt any oem coils, from there i just used oem coils they cost $23. i was very dissappointed with okada. im glad i got bhr now for my next project. https://www.rx8club.com/series-i-major-horsepower-upgrades-93/rear-fi-daily-driver-project-179348/

@!!narotordo

Can someone tell me if this is set up right? I dont have the instructions

Mr.&Mrs.Magic

iTrader: (3)

If you got a day to wait PM me a fax number and I'll fax the complete manual. No scanner so that's out on my end, suppose I could take pics. Lemme know if this will help you any.