Notices
Series I Major Horsepower Upgrades This is the place to discuss Super Chargers and Turbos, Nitrous, Porting, etc

Carbon8 Build

Thread Tools
 
Search this Thread
 
Rate Thread
 
Old 08-02-2013, 11:07 AM
  #326  
Yank My Wankel
Thread Starter
iTrader: (4)
 
Carbon8's Avatar
 
Join Date: Nov 2009
Location: Buffalo, NY
Posts: 2,207
Likes: 0
Received 6 Likes on 6 Posts
Originally Posted by FazdaRX_8
the right dwell for those coils are posted on the forums by oltman....
I'll look for them, I don't think its a dwell issue.

After re-gapping the plugs it only happens very seldom and only in 4th gear and up. I noticed that during it my A/F dumps below 11. So Im just going to wait on it until we can finish tuning, and not romp on it.
Old 08-07-2013, 08:39 PM
  #327  
Yank My Wankel
Thread Starter
iTrader: (4)
 
Carbon8's Avatar
 
Join Date: Nov 2009
Location: Buffalo, NY
Posts: 2,207
Likes: 0
Received 6 Likes on 6 Posts
Looking for some input.

Couple days ago I started getting hard hot starts, and white smoke out of the exhaust. Long story short Cam recommended Porosity tabs, after I used the tabs smoke went away. Now today the smoke seems to be back. I realized my hard hot starts where a tuning issue, and is all straight now no it starts and runs great but I am still getting white smoke. I have not driven the car at all, Cam recommends I put 100 miles on and see how it effects it.

Stats;

Coolant system pressure test held firm at 20 PSI both cold and Hot
Oil sample sent to blackstone today for testing contaminants.
Plugs cleaned

Idle Log
A/F 14.41
STFT range;.24-1
LTFT: 2.97 (constant)
MAF; 5.5 g/s
MAF; 1.23V
Ign Tim Sep; -15 degrees

Only thing out of the ordinary is LTFT, other than that the car runs great!

Here are the idle videos, the after video its faint but you can almost here what appears to sound like deep puffs (you can notice when the smoke is abruptly pushed away)


Old 08-07-2013, 11:02 PM
  #328  
SARX Legend
iTrader: (46)
 
9krpmrx8's Avatar
 
Join Date: Jan 2007
Location: San Antonio, Texas
Posts: 33,784
Received 452 Likes on 366 Posts
How much premix are you running and what type? Also what midpipe do you have? Does the exhaust smell sweet? Burning oil has a distinct smell but it can be white as well.
Old 08-08-2013, 06:48 AM
  #329  
Yank My Wankel
Thread Starter
iTrader: (4)
 
Carbon8's Avatar
 
Join Date: Nov 2009
Location: Buffalo, NY
Posts: 2,207
Likes: 0
Received 6 Likes on 6 Posts
4 oz protek premix, and SOHN running protek. Exotic Speed midpipe.

From what I have seen its not a lot of smoke, and I have never smelled burning coolant so I can't tell if it is.
Old 08-08-2013, 07:46 AM
  #330  
Yank My Wankel
Thread Starter
iTrader: (4)
 
Carbon8's Avatar
 
Join Date: Nov 2009
Location: Buffalo, NY
Posts: 2,207
Likes: 0
Received 6 Likes on 6 Posts
Yeah, it does not smell sweet at all, It burns the nostrils, smells dry. Hard to describe, made me light headed with just a little bit.

Hope that helps
Old 08-08-2013, 07:57 AM
  #331  
Illudium Q-36 Space Moderator
iTrader: (1)
 
Kane's Avatar
 
Join Date: Jan 2007
Location: PCB
Posts: 6,364
Received 41 Likes on 31 Posts
Some like that when it's warmed up too? It might be too much pre-mix. Have you tried just a regular tank of gas?
Old 08-08-2013, 08:05 AM
  #332  
Yank My Wankel
Thread Starter
iTrader: (4)
 
Carbon8's Avatar
 
Join Date: Nov 2009
Location: Buffalo, NY
Posts: 2,207
Likes: 0
Received 6 Likes on 6 Posts
Not yet, I will next fill up, it goes away after a while too.

Drove it to work today; 5 miles and when I got there and let it idle for a bit the smoke was gone.

Im chalking it up to a lil rich, and premix.
Old 08-08-2013, 09:13 AM
  #333  
SARX Legend
iTrader: (46)
 
9krpmrx8's Avatar
 
Join Date: Jan 2007
Location: San Antonio, Texas
Posts: 33,784
Received 452 Likes on 366 Posts
When you say 4oz, you mean to a tank?
Old 08-08-2013, 09:17 AM
  #334  
Yank My Wankel
Thread Starter
iTrader: (4)
 
Carbon8's Avatar
 
Join Date: Nov 2009
Location: Buffalo, NY
Posts: 2,207
Likes: 0
Received 6 Likes on 6 Posts
Yup, 4oz per tank.
Old 08-08-2013, 09:20 AM
  #335  
SARX Legend
iTrader: (46)
 
9krpmrx8's Avatar
 
Join Date: Jan 2007
Location: San Antonio, Texas
Posts: 33,784
Received 452 Likes on 366 Posts
Oh ok, I thought you meant per gallon,
Old 08-08-2013, 09:22 AM
  #336  
Yank My Wankel
Thread Starter
iTrader: (4)
 
Carbon8's Avatar
 
Join Date: Nov 2009
Location: Buffalo, NY
Posts: 2,207
Likes: 0
Received 6 Likes on 6 Posts
That would be insanely expensive
Old 08-12-2013, 12:27 PM
  #337  
Yank My Wankel
Thread Starter
iTrader: (4)
 
Carbon8's Avatar
 
Join Date: Nov 2009
Location: Buffalo, NY
Posts: 2,207
Likes: 0
Received 6 Likes on 6 Posts
Misfire Subsidiary

Instead of making a new thread I am hopeful this one gets enough attention to help.

Been suffering a misfire since my rebuild, at first it was audible during 4th gear and up pulls only over 7K RPM under WOT. No flashing CEL no codes, just audible popping noise.

I re-gapped plugs and reset NVRAM, this solved the problem for a couple days then it returned.

Next I pulled the wires off the trailing plugs, to ensure that the leading coils are in good working condition. Car fired right up and idle was normal, so I do not have a leading plug problem. Also re-gapped a little lower as was recommended by Cam at Pettit.

So now the popping noise is gone but my new symptoms.

Only happens in 4th gear and up; Runs really rich at 4K with 20% load, 11.4-12 A/F If I let up the throttle the needle will spike down to 10, sometimes it will also cause a flashing CEL. No noise, no hesitation just a flashing CEL. I noticed my cruising A/F is more around 13.4. Doing logs my ignition separation goes for -15 to +5.

Running BHR coils (on OE Dwell), NGK plugs Gapped to .033, 93 Octane fuel W/ 4 oz Protek-R per tank, SOHN adapter with protek-R reservoir OE OMP rates.

Also want to add, I know 14.2 is peferct for little load and cruising, for an NA 8.

What is considered to rich, what is considered to lean?


Thoughts/Suggestions?

Go!
Old 08-12-2013, 01:04 PM
  #338  
SARX Legend
iTrader: (46)
 
9krpmrx8's Avatar
 
Join Date: Jan 2007
Location: San Antonio, Texas
Posts: 33,784
Received 452 Likes on 366 Posts
At cruise with low load, you should be close to Stoich. Have you tried not using the OE dwell (see timing thread)?
Old 08-12-2013, 01:58 PM
  #339  
Yank My Wankel
Thread Starter
iTrader: (4)
 
Carbon8's Avatar
 
Join Date: Nov 2009
Location: Buffalo, NY
Posts: 2,207
Likes: 0
Received 6 Likes on 6 Posts
No,

Im not there yet

I know I should try it, but I want to rule everything else out first.
Old 08-12-2013, 05:05 PM
  #340  
Illudium Q-36 Space Moderator
iTrader: (1)
 
Kane's Avatar
 
Join Date: Jan 2007
Location: PCB
Posts: 6,364
Received 41 Likes on 31 Posts
14.7 is what you should see at cruise.
Old 08-14-2013, 07:53 AM
  #341  
Yank My Wankel
Thread Starter
iTrader: (4)
 
Carbon8's Avatar
 
Join Date: Nov 2009
Location: Buffalo, NY
Posts: 2,207
Likes: 0
Received 6 Likes on 6 Posts
I would just like to say, I came across this little tid bit today. Will be testing my system as soon as I get this built either today or tomorrow.

Thanks Scott, and the SARX crew for mocking this up.
RX-8 Hymee Supercharger Install - Smoke Tester
Old 08-14-2013, 09:39 AM
  #342  
SARX Legend
iTrader: (46)
 
9krpmrx8's Avatar
 
Join Date: Jan 2007
Location: San Antonio, Texas
Posts: 33,784
Received 452 Likes on 366 Posts
It works great man, I got that exact smoke machine on Amazon cheap.
Old 08-14-2013, 09:44 AM
  #343  
Yank My Wankel
Thread Starter
iTrader: (4)
 
Carbon8's Avatar
 
Join Date: Nov 2009
Location: Buffalo, NY
Posts: 2,207
Likes: 0
Received 6 Likes on 6 Posts
Yeah, Im gona run to party city, they sell it for the same price as amazon and I don't have to wait till shipping.

I fixed one vacuum leak last night off my VFAD nipple, but I can still tell I have another one somewhere. Progress is progress i suppose.

Guess this is what they meant by projects are never finished
Old 08-14-2013, 01:15 PM
  #344  
Drummond Built
iTrader: (6)
 
WTBRotary!'s Avatar
 
Join Date: Aug 2008
Location: DFW, Texas
Posts: 3,703
Likes: 0
Received 0 Likes on 0 Posts
Builds like this make me nervous to install my engine... I hope i don't run into any problems
Old 08-14-2013, 01:17 PM
  #345  
SARX Legend
iTrader: (46)
 
9krpmrx8's Avatar
 
Join Date: Jan 2007
Location: San Antonio, Texas
Posts: 33,784
Received 452 Likes on 366 Posts
Send it to me, I will slap it in and throw 10psi at it
Old 08-14-2013, 01:21 PM
  #346  
Yank My Wankel
Thread Starter
iTrader: (4)
 
Carbon8's Avatar
 
Join Date: Nov 2009
Location: Buffalo, NY
Posts: 2,207
Likes: 0
Received 6 Likes on 6 Posts
At this point its honestly just a ton of little things here and their, nothing that prevent driving oe is giving me complicated issues, just things that take time.

Sometime these cars turn into moody little b*tch's and mines on a streak!
Old 08-14-2013, 01:28 PM
  #347  
SARX Legend
iTrader: (46)
 
9krpmrx8's Avatar
 
Join Date: Jan 2007
Location: San Antonio, Texas
Posts: 33,784
Received 452 Likes on 366 Posts
Are you still have hard starts?
Old 08-14-2013, 01:41 PM
  #348  
Yank My Wankel
Thread Starter
iTrader: (4)
 
Carbon8's Avatar
 
Join Date: Nov 2009
Location: Buffalo, NY
Posts: 2,207
Likes: 0
Received 6 Likes on 6 Posts
Nope, and changed dwell and have not had a misfire issue yet, but it is running rich and will stall after cruising and coming to a stop so I know I still have a leak somewhere. It fires right up every time though.
Old 08-16-2013, 07:46 AM
  #349  
Yank My Wankel
Thread Starter
iTrader: (4)
 
Carbon8's Avatar
 
Join Date: Nov 2009
Location: Buffalo, NY
Posts: 2,207
Likes: 0
Received 6 Likes on 6 Posts
First fogger run showed the MAF sensor was leaking in the AEM housing, need to fab up a canister before the nozzle as I am having the same problem of excess fluid in the fog lines.

Hopefully get this all straightened out this afternoon for some weekend fun.
Old 08-16-2013, 02:13 PM
  #350  
Registered
iTrader: (1)
 
FazdaRX_8's Avatar
 
Join Date: Jun 2009
Posts: 2,019
Likes: 0
Received 5 Likes on 5 Posts
what did you change in the tuning to improve the starting?

what do you mean fog lines?

what are Porosity tabs?

are you sure the white smoke isn't condensation or something to do with the air pump.

told you the dwell would help!


You have already rated this thread Rating: Thread Rating: 0 votes,  average.

Quick Reply: Carbon8 Build



All times are GMT -5. The time now is 09:36 PM.