4.778 Final Drive For $296
01-02-2006, 05:12 PM
#228
I am just guessing here but I would be willing to bet that the 4.77 gear will cut between .25-.30s off of the 1/4 mile times, with no other changes to the car. Let me know if I am wrong when someone makes the swap, willya?
CRH
CRH
01-02-2006, 06:24 PM
#230
Registered User
Join Date: Oct 2005
Location: rialto ca
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
yeah with this car it need to keep the revs up with a 4.77 it would make a big dif in this car for u guys that r looking japan company feed makes 4.77 gears for r car
01-02-2006, 07:27 PM
#232
Stuck in a love triangle
The reason why I am interested in this is because it should speed up the somewhat lagged delivery time of the engine's power. Nothing too incredible but it should feel a little more enjoyable under WOT. I am only concerned that going through each gear won't feel as smooth as stock.
01-03-2006, 07:40 PM
#235
Registered User
Join Date: Dec 2005
Posts: 4
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Slick8
You need the following besides the usual shop tools,
experience transmission mechanic, not a DIY
the service manual for torque specs
a press to pull off/seat the bearings
side seals and companion flange seal (if they are old, possible reuse)
silicone sealant
magnetic dial gauge to measure backlash
tooth marking compound
caliper and ruler to measure pinion height (possibly a few spacers)
shim kit
engine stand
locknut
2 qt. GL-5 gear oil
PS The NyQuil is hitting me hard now, very sleepy, goodnight folks...
experience transmission mechanic, not a DIY
the service manual for torque specs
a press to pull off/seat the bearings
side seals and companion flange seal (if they are old, possible reuse)
silicone sealant
magnetic dial gauge to measure backlash
tooth marking compound
caliper and ruler to measure pinion height (possibly a few spacers)
shim kit
engine stand
locknut
2 qt. GL-5 gear oil
PS The NyQuil is hitting me hard now, very sleepy, goodnight folks...
Hey Slick,
Hope you are felling better. Thanks for the comprehensive outline. Another quest. I have is do I need any news bearings or anythign else in the rear housing or do you just swap the ring and pinion and that is that??
I have the centre from Kia and some people were talking about spacers etc.??
The ring/pinion goes off next week to get cryoed so it will be in late next week if all goes well.
Your help on this one would be most appreciated.
01-04-2006, 01:43 PM
#241
Registered User
Join Date: Jan 2005
Location: Visalia, CA
Posts: 522
Likes: 0
Received 0 Likes
on
0 Posts
Chances are Feed is just using the same one that Slick8 bought from Kia.
Originally Posted by toca
its like 150 200 bucks but with feed u know u getting very good ****
01-09-2006, 09:43 PM
#247
Registered
Thread Starter
Join Date: Oct 2004
Location: Philly
Posts: 332
Likes: 0
Received 0 Likes
on
0 Posts
My flu and bronchitis finally broke in the last few days. I couldn't move or do anything, very depressing...
Going back to work tomorrow and need a week to catchup at work, everything at the crib, and a wash-vacuum for my RX-8.
I plan on installing the ring and pinion the weekend after next. Hope it fits.
Going back to work tomorrow and need a week to catchup at work, everything at the crib, and a wash-vacuum for my RX-8.
I plan on installing the ring and pinion the weekend after next. Hope it fits.
