RX8 experiment PP exhaust engine build (pic inside)
#1
Registered
Thread Starter
RX8 experiment PP exhaust engine build (pic inside)
Since Rx8 debut, old Rotary community all have
What if ? 13B MSP have PP exhaust!!!
Now after a few years of planning &developing
This is sec prototype my friend build for Rx8
First one is Turbo version~ This one is NA Build
Update 10/26 2022 at page 16
Here is Dyno sheet using Dynapack
Solid line is 13B MSP Ext PP
Dot line is stock 13B MSP
What if ? 13B MSP have PP exhaust!!!
Now after a few years of planning &developing
This is sec prototype my friend build for Rx8
First one is Turbo version~ This one is NA Build
Update 10/26 2022 at page 16
Here is Dyno sheet using Dynapack
Solid line is 13B MSP Ext PP
Dot line is stock 13B MSP
Last edited by Diyman25; 10-26-2022 at 06:06 PM.
The following users liked this post:
sharingan 19 (05-22-2022)
#3
Registered
Thread Starter
Originally Posted by Brettus
Awesome ! Been hoping someone would do this for a long time. Very keen to see how it all pans out.
The big question : what have you used to seal the side exhaust ports ? Looks like JB weld or similar .....
Also , exhaust header has no turbo flange ?
The big question : what have you used to seal the side exhaust ports ? Looks like JB weld or similar .....
Also , exhaust header has no turbo flange ?
This one is NA build , turbo one already been runing for some time
#7
77 cylinders, 4 rotors...
Can't wait to see Team's reaction to this when he emerges again. I miss/don't miss his input. You know what I mean?
The following users liked this post:
kops (10-29-2021)
#8
I miss MazdaManiac's input too. I'm sure there are others as well. But at some point you become such a *****, people don't care if you give good advice.
The following 3 users liked this post by Killawatts:
#9
77 cylinders, 4 rotors...
I would love to see more about this. I like to see people actually build things.
#11
No respecter of malarkey
iTrader: (25)
my reaction is simply to wait and see; my position has always been that the cost and effort won’t justify the input of resources and hassle required for reasons illustrated and discussed in detail in various other threads on the subject
**until someone demonstrates otherwise**.
Been waiting patiently for 10+ years and still am …
kilawatts, with all sincerity; I’m sad for you.
.
**until someone demonstrates otherwise**.
Been waiting patiently for 10+ years and still am …
kilawatts, with all sincerity; I’m sad for you.
.
#14
Registered
Thread Starter
Originally Posted by TeamRX8
Looks fairly unresponsive compared to doing the same with a strong Renesis engine
just listen to the difference here on the downshifts:
It’s easy to see why though. Once you change from a non-overlap intake-exhaust cycle scenario then all the rules change too. Nobody is picking up on one of the most basic ones that’s right in front of their face. No surprise at all, really.
.
just listen to the difference here on the downshifts:
It’s easy to see why though. Once you change from a non-overlap intake-exhaust cycle scenario then all the rules change too. Nobody is picking up on one of the most basic ones that’s right in front of their face. No surprise at all, really.
.
Car is not full tune yet , just start up ready to brake in
Is not fair to compare to this stage
#18
Registered
Thread Starter
Originally Posted by Fickert
Interesting!
I thought this project was dead in the water. Any thoughts on going to a dyno?
I thought this project was dead in the water. Any thoughts on going to a dyno?
Will ask my friend strap to Dyno that I use for my Rx8
#21
To be fair in this current environment 1 month is not very long. Most good dyno’s around me which are many are all tied up for the next 2-3 months.
So no surprise. Looks a bit slow Erving compared to stock but not saying that can’t be cleaned up with tuning. Cool build for sure.
So no surprise. Looks a bit slow Erving compared to stock but not saying that can’t be cleaned up with tuning. Cool build for sure.