Williard

iTrader: (18)

Waiting....


Travis

Brettus

iTrader: (2)

That shield should really help with underhood temps and it looks really smart too !
Finally had enough of people messing with your hashtag i see LOL

firecran

iTrader: (3)

^yep the kids will play

Williard

iTrader: (18)

And will continue until you follow through with what you've promised.

Travis

firecran

iTrader: (3)

You gotta wait till I get back from DGRR 2016.

Williard

iTrader: (18)

but why!?!?

I dont have that much patience....
Im developing a twitch dammit
Travis

Ian_D

What are your thoughts on transmissions now that you've upped your power? For example, are you happy with what you've got, are you looking to avoid running where heat may be a problem, are you fitting an oil cooler or are you looking to see how it goes?

FWIW I'm concerned about temperatures on track with my EFR 7060 build so am fitting a transmission oil cooler.

firecran

iTrader: (3)

I haven't pushed this setup yet.
My only transmission finding so far is I prefer the Jdm rx-8 5spd over the stock 6spd.
I'm going to see how it goes but I don't think i'll need a trans cooler.
Dan would be a good person to ask about adding one.

Also, do you think that 7060 is to small? What's your reason for not going with a 8374?
8374 is great, down low response is just there and now.
I'm extremely please with it.

Ian_D

Steve, thanks.

Apologies, that should be EFR 7670. I wobbled backwards and forwards over 7670 or 8374, eventually deciding that the lower power/quicker response was better for my use than higher power.

firecran

iTrader: (3)

Ok cool, that sucker is going to spool lighting quick!

firecran

iTrader: (3)

Bro that sounds like a classic case of the Renesis
Yep, you need your REW fix.

Brettus

iTrader: (2)

And make lots of hot air ................he better have some real good intercooling going on if he is tracking it.

firecran

iTrader: (3)

Yep
I would install a speed sensor to ensure he's not over spinning it too.

Tem

I will be going! hope to see you there!

Ian_D

I've a fully ducted 3" x 12" x 18" Garrett core (lovely design and build with proper cooling fins) exhausting out the bonnet (plug for my aerodynamics thread here) with a temperature gauge giving me both inlet and outlet temperatures and a plan to fit water injection if needed. I want to avoid hijacking Cran's build thread so please save any discussion for mine that I'll put up over the weekend.
I like the idea of a speed sensor as it takes me back to my days dealing with military jet engines. However, quite a few FDs have the 7670 and AFAIK nobody has reported problems; additionally, cost is an issue as sensors are $250 over here and there's wiring, controller/processor and display to pay for too (I'm looking to fit the Adaptronic ECU and a Nexus tablet, and will look to see what that can do when I get time).

firecran

iTrader: (3)

On the way to DGRR 2016



.

boostdtalon

Have fun! Oh did I mention you are a bad influence? You are making it really hard not to get an RX8 and do REW things to it.


Just so happens I have an REW and a GT40RS waiting for an engine bay to rest in.

firecran

iTrader: (3)

Sweet!! Do it you won't regret it

firecran

iTrader: (3)

DGRR 2016 was great had a blast again, lots of great people and rotaries there. Already itching to go back.

I'm thankful to have won First Place RX-8 for DGRR 2016 at the car show.
There were lots of really nice 8's that showed up.
More pics and videos to follow later.




.

firecran

iTrader: (3)

Some Killboy Dragon shots...















.

9krpmrx8

iTrader: (46)

Nice pics. "1rst" place? I have never seen that abbreviation before.

firecran

iTrader: (3)

I know

firecran

iTrader: (3)

Couple more...

Williard

iTrader: (18)

Still aint got none of them there Movin' Picture shows up there....

i'll wait


Travis

firecran

iTrader: (3)

got to upload them but haven't had time