throwing codes like crazy
#1
Registered
Thread Starter
iTrader: (1)
Join Date: May 2003
Location: PA
Posts: 3,754
Likes: 0
Received 0 Likes
on
0 Posts
throwing codes like crazy
got a good ol check engine light today...
------------------------------------------------------------
MIL is ON Stored Trouble Codes Present
Misfire Monitoring Complete
Fuel Sys. Monitoring Complete
Component Monitoring Complete
Catalyst Monitoring Incomplete
Evaporative System Monitoring Incomplete
Sec. Air System Monitoring Incomplete
O2 Sensor Monitoring Complete
O2 Sensor Heater Monitoring Complete
Fuel Sys1-Open Loop Driving
ECU #=10
MIL is ON
Vehicle Reports 1 Stored Trouble Code(s)
TC1 -P2070
P2070 Intake Manifold Tuning (IMT) Valve Stuck Open a)
Pending Code 1 -P0020--P0020 a) "A" Camshaft Position Actuator Circuit Bank 2
Pending Code 2 -P7000--Trouble code definition not found
-------------------------------------------------------------------------
so... umm anyone have an idea how i went from never having a code to 3 codes instantly?
I tried resetting the codes and resetting the computer and they cam back right away
------------------------------------------------------------
MIL is ON Stored Trouble Codes Present
Misfire Monitoring Complete
Fuel Sys. Monitoring Complete
Component Monitoring Complete
Catalyst Monitoring Incomplete
Evaporative System Monitoring Incomplete
Sec. Air System Monitoring Incomplete
O2 Sensor Monitoring Complete
O2 Sensor Heater Monitoring Complete
Fuel Sys1-Open Loop Driving
ECU #=10
MIL is ON
Vehicle Reports 1 Stored Trouble Code(s)
TC1 -P2070
P2070 Intake Manifold Tuning (IMT) Valve Stuck Open a)
Pending Code 1 -P0020--P0020 a) "A" Camshaft Position Actuator Circuit Bank 2
Pending Code 2 -P7000--Trouble code definition not found
-------------------------------------------------------------------------
so... umm anyone have an idea how i went from never having a code to 3 codes instantly?
I tried resetting the codes and resetting the computer and they cam back right away
#5
Registered
Thread Starter
iTrader: (1)
Join Date: May 2003
Location: PA
Posts: 3,754
Likes: 0
Received 0 Likes
on
0 Posts
a) using a canscan.... and yea, i don't see the other 2 codes listed in the service manual... and i sure as hell shouldn't need to worry about camshafts -shrug-
b) haven't changed the intake... only installed a supercat a week ago and reprogrammed my cz box yesterday
updated - i just pulled my cz box thinking i'll be taking it to the dealer soon. Took it for a spin and the CEL went off. Not sure if maybe i have a bad connection in the box, or since the CEL takes 2 driving cycles if it will come back on tomorrow morning (but that shouldn't be the case as i didn't kill the battery or reset the codes last trip). We will see....
b) haven't changed the intake... only installed a supercat a week ago and reprogrammed my cz box yesterday
updated - i just pulled my cz box thinking i'll be taking it to the dealer soon. Took it for a spin and the CEL went off. Not sure if maybe i have a bad connection in the box, or since the CEL takes 2 driving cycles if it will come back on tomorrow morning (but that shouldn't be the case as i didn't kill the battery or reset the codes last trip). We will see....
#10
Registered
Thread Starter
iTrader: (1)
Join Date: May 2003
Location: PA
Posts: 3,754
Likes: 0
Received 0 Likes
on
0 Posts
I talked with Harrison and the 2 strange pending codes were just some strange unknown error... doesn't show up now with my old software or my new software he just sent me -shrug-
Thread
Thread Starter
Forum
Replies
Last Post