Single Oil Cooler
11-23-2009, 10:41 PM
#52
SARX Legend
Thread Starter
iTrader: (46)
Okay guys, I owe Grungepup a steak dinner at Ruth Chris. We finished up tonight and over all I am happy as a fat kid eating cake. Next time I have the bumper off I will do some minor trimming but only because I know the bumper is touching the cooler a bit. As far as how it performs?
All I have to say is........................
HELLO 90PSI!!!!!!!
Pretty much anywhere in the very upper rev range it gets to 90PSI. I will start tracking data tomorrow.
All I have to say is........................
HELLO 90PSI!!!!!!!
Pretty much anywhere in the very upper rev range it gets to 90PSI. I will start tracking data tomorrow.
11-24-2009, 10:16 AM
#57
SARX Legend
Thread Starter
iTrader: (46)
This mod is pretty straight forward, you just use an adapter that screws into the block, one for feed and one for return. Then you plumb the hoses and mount the cooler. I am happy with my setup but I think have a two cooler setup is okay too if you replace the stock coolers and run them using the existing lines. It would be much less work. I am sure you can find adapters to allow you to hook up better after market coolers and eliminate the stock flow thermostats.
11-24-2009, 11:28 AM
#58
wouldnt that much of an increase in oil pressure result in less oil being filtered? You are saturating the rear bypass which allows the engines pressure to go above its relief pressure?
So would it not be wise to do a rear bypass modification so more oil would be getting to your filter?
This intial observation does suggest that there is a lot of restriction/pressure loss in supplying the two coolers. restrictive thermosat in the cooler and lenght of tubes I guess.
So would it not be wise to do a rear bypass modification so more oil would be getting to your filter?
This intial observation does suggest that there is a lot of restriction/pressure loss in supplying the two coolers. restrictive thermosat in the cooler and lenght of tubes I guess.
11-24-2009, 12:20 PM
#60
11-24-2009, 12:44 PM
#61
Super Moderator
11-24-2009, 12:56 PM
#62
Super Moderator
I wonder what the OP is for AT (Single LH) Oil Cooler?
11-24-2009, 01:13 PM
#63
SARX Legend
Thread Starter
iTrader: (46)
Oh okay, my memory failed then I thought the 09's pressure topped out at 130PSI or so. I'm getting a little confused about the bypass stuff. My oil heats up much faster and my oil pressures are about 10-15PSI higher across the board.
Warmed up at idle I used to see about 20PSI and now I see about 30PSI based on what I saw this morning and last night. At redline (about) I was seeing mid 70's and now I see right at 90PSI. But as I said, I have not logged many data points yet so we will see how it averages out.
11-24-2009, 05:07 PM
#65
SARX Legend
Thread Starter
iTrader: (46)
Yes sir. here are some pics. And yes I know the hose will get hit with debri, I will be installing screens very soon. But this hose is designed to be exposed to tough situation on outside hydraulic equipment which is why it is so expensive. Grungepup can attest to it's strength as he was the one using metal tin snips to cut it 
Passenger side fog clearance
Passenger side fog clearance
Last edited by 9krpmrx8; 11-24-2009 at 05:21 PM.
11-24-2009, 05:44 PM
#67
SARX Legend
Thread Starter
iTrader: (46)
Thanks. It needs some adjustment and on the next install I will move the thermostat way back but we were winging it and I am no fabricator by any stretch of the imagination.
11-24-2009, 08:19 PM
#70
SARX Legend
Thread Starter
iTrader: (46)
Yeah that was a good idea except for the little spider cracks in the paint from distorting the bumper 
I should have done it at a different angle but it's only noticable to me. Now I just need to trim that bottom of the cooler with a real cutter this weekend at my dads so I can get the bumper back nice and perfect. It's bugging me.
I should have done it at a different angle but it's only noticable to me. Now I just need to trim that bottom of the cooler with a real cutter this weekend at my dads so I can get the bumper back nice and perfect. It's bugging me.
11-24-2009, 08:53 PM
#71
FLAME ON!
Join Date: Jul 2009
Location: Strip Club
Posts: 948
Likes: 0
Received 0 Likes
on
0 Posts
I recently purchased this single Fluidyne oil cooler that will sit front and center perfectly at the bottom of the radiator. My factory coolers have seen 100,000 miles of road debris without screens and are banged to ****. So they will be removed and the space used for brake ducting.
Anyway, I will have the fittings and hoses made at a local hydraulics shop after I measure everything and determine the shortest route for the the lines.
Opinions welcome.
This cooler has #12 AN fiitings, is made of heavy Gauge aluminum. The unit measures 28" x 5" x 5 1/4" and has 6 rows of cooling tubes.
Anyway, I will have the fittings and hoses made at a local hydraulics shop after I measure everything and determine the shortest route for the the lines.
Opinions welcome.
This cooler has #12 AN fiitings, is made of heavy Gauge aluminum. The unit measures 28" x 5" x 5 1/4" and has 6 rows of cooling tubes.
So how are your temps?
11-25-2009, 12:42 AM
#72
SARX Legend
Thread Starter
iTrader: (46)
I know of two others but I did not know rotary resurrection did this. Mt temps are great, just came from decent drive and they stayed between 180-185 degrees F. Pressures look good too.
11-25-2009, 05:26 AM
#75
Ayrton Senna Forever
wouldnt that much of an increase in oil pressure result in less oil being filtered? You are saturating the rear bypass which allows the engines pressure to go above its relief pressure?
So would it not be wise to do a rear bypass modification so more oil would be getting to your filter?
This intial observation does suggest that there is a lot of restriction/pressure loss in supplying the two coolers. restrictive thermosat in the cooler and lenght of tubes I guess.
So would it not be wise to do a rear bypass modification so more oil would be getting to your filter?
This intial observation does suggest that there is a lot of restriction/pressure loss in supplying the two coolers. restrictive thermosat in the cooler and lenght of tubes I guess.
Unbeliavable, but it seems to be true, if I see PhillipM and 9krpmrx8 mod.