Notices
Series I AT-Specific Performance Mods Discuss engine and transmission modifications for your AT equipped RX-8

BigBadChris and the little turbo RX8

Thread Tools
 
Rate Thread
 
Old Aug 21, 2015 | 10:47 AM
  #226  
BigBadChris's Avatar
Thread Starter
Registered
iTrader: (4)
 
Joined: Aug 2014
Posts: 680
Likes: 28
From: Dallas TX
I have the original S1 starter, and I replaced the battery in October. It is an Optima red top, 720 CCA. When it fires up normally (90% of the time) it turns over immediately.
Reply
Old Aug 21, 2015 | 11:08 AM
  #227  
shadycrew31's Avatar
WENTGERMAN
iTrader: (6)
 
Joined: Apr 2008
Posts: 5,806
Likes: 31
From: Burbs,PA
Originally Posted by BigBadChris
I have the original S1 starter, and I replaced the battery in October. It is an Optima red top, 720 CCA. When it fires up normally (90% of the time) it turns over immediately.
Yeah get an upgraded s2 starter it should help out. Also if you can get the engine tested again and post the readings on here with the RPM it was tested at we can give you a better idea of engine condition.

Just as a side note, I do not trust Scott either based on past experiences.

I truly hope he pulls through for you.
Reply
Old Aug 21, 2015 | 11:42 AM
  #228  
BigBadChris's Avatar
Thread Starter
Registered
iTrader: (4)
 
Joined: Aug 2014
Posts: 680
Likes: 28
From: Dallas TX
I have one of the compression tests at home. It is not a hot start issue, or a cold start issue. Hot, cold, day, night, it makes no difference. Once in a while, it just needs to crank more than the other times. I have driven it for an hour, parked it, and restarted it two minutes later and it fired right up. Ive also come out in the morning and it hesitated. I cannot find any rhyme or reason
Reply
Old Aug 21, 2015 | 11:56 AM
  #229  
Brettus's Avatar
Boosted Kiwi
iTrader: (2)
 
Joined: Apr 2006
Posts: 20,839
Likes: 1,796
From: Y-cat-o NZ
Originally Posted by BigBadChris
I have one of the compression tests at home. It is not a hot start issue, or a cold start issue. Hot, cold, day, night, it makes no difference. Once in a while, it just needs to crank more than the other times. I have driven it for an hour, parked it, and restarted it two minutes later and it fired right up. Ive also come out in the morning and it hesitated. I cannot find any rhyme or reason
Don't sweat it .................
Reply
Old Aug 21, 2015 | 11:59 AM
  #230  
BigBadChris's Avatar
Thread Starter
Registered
iTrader: (4)
 
Joined: Aug 2014
Posts: 680
Likes: 28
From: Dallas TX
A dissenting opinion from the Southern Hemisphere. Thanks for weighing in, Brett. I hope all is going well with your build. If you dont mind my asking, did you go with a Tial housing, or did you stick with Garrett?
Reply
Old Aug 21, 2015 | 12:00 PM
  #231  
Brettus's Avatar
Boosted Kiwi
iTrader: (2)
 
Joined: Apr 2006
Posts: 20,839
Likes: 1,796
From: Y-cat-o NZ
Originally Posted by BigBadChris
I have the original S1 starter,
And you are complaining ??????? Get the upgraded starter already FFS !

Last edited by Brettus; Aug 21, 2015 at 12:03 PM.
Reply
Old Aug 21, 2015 | 12:02 PM
  #232  
Brettus's Avatar
Boosted Kiwi
iTrader: (2)
 
Joined: Apr 2006
Posts: 20,839
Likes: 1,796
From: Y-cat-o NZ
Originally Posted by BigBadChris
A dissenting opinion from the Southern Hemisphere. Thanks for weighing in, Brett. I hope all is going well with your build. If you dont mind my asking, did you go with a Tial housing, or did you stick with Garrett?
Tial don't make a T3 twin scroll so ................... Garrett .
Reply
Old Aug 21, 2015 | 12:09 PM
  #233  
BigBadChris's Avatar
Thread Starter
Registered
iTrader: (4)
 
Joined: Aug 2014
Posts: 680
Likes: 28
From: Dallas TX
I am not complaining about the starting speed in general, just that one out of every ten times, it takes longer, but always five seconds or less. The only reason I am talking about starting speed is that it lead us down this weird path. Had it turned over the normal way yesterday, we wouldnt be having this conversation.

Last edited by BigBadChris; Aug 21, 2015 at 12:19 PM.
Reply
Old Aug 21, 2015 | 12:13 PM
  #234  
Brettus's Avatar
Boosted Kiwi
iTrader: (2)
 
Joined: Apr 2006
Posts: 20,839
Likes: 1,796
From: Y-cat-o NZ
Originally Posted by BigBadChris
I am not complaining about the starting speed in general, just that one out of every ten times, it takes longer, but always five seconds or less.
Just get the UG starter and be prepared to be amazed !

anyway .... does this mean you have the car back or ... not ? I'm confused .
Reply
Old Aug 21, 2015 | 12:27 PM
  #235  
BigBadChris's Avatar
Thread Starter
Registered
iTrader: (4)
 
Joined: Aug 2014
Posts: 680
Likes: 28
From: Dallas TX
I do not have it back.

Scott was testing it in the shop yesterday, and we stumbled into this tangent.

Fingers crossed for dyno test next week
Reply
Old Aug 21, 2015 | 08:01 PM
  #236  
TeamRX8's Avatar
Registered
iTrader: (25)
 
Joined: Apr 2005
Posts: 26,936
Likes: 2,140
Originally Posted by BigBadChris
@Team: I may not know a lot, but I can repeat what I hear on the phone
Originally Posted by BigBadChris
You're right, i had said stuck closed, and I have meant stuck open


Remember my prior advice to STFU and wait for the final results? It was intended to help avoid the total clusterf-ck that this thread has become. The desire to look like a hero in advance is always too alluring. And of course the Scott-haters never miss their opportunity to sow doubt with the usual cheap shots that you so kindly keep setting up for them. There was also some discussion about proper financial planning, which when going turbo on a older daily driven engine means being prepared for the inevitable.

At this point the hole is so deep you might as well just keep posting/blabbing until you pop up in China.
Reply
Old Aug 21, 2015 | 08:39 PM
  #237  
BigBadChris's Avatar
Thread Starter
Registered
iTrader: (4)
 
Joined: Aug 2014
Posts: 680
Likes: 28
From: Dallas TX
"Look like a hero in advance".....I have not bragged one time about what I am hoping to achieve. Instead, I am coming in here, reporting my progress, and asking for advice. Clearly that was too much to ask.

Please, give me some more financial advice. Did I say "Oh ****, I cant afford a rebuild, I am screwed!!!!!" No. I dont want to do a rebuild, no car owner does. We want the car to run, and we want to enjoy driving it. No one enjoys the idea of a damaged motor. I knew a rebuild was coming eventually, no RX8 lives forever. I was just hoping to get more time out of it.

China, here I come!

Last edited by BigBadChris; Aug 21, 2015 at 09:16 PM.
Reply
Old Aug 22, 2015 | 11:04 AM
  #238  
DAT2RTR's Avatar
Registered
 
Joined: Jun 2014
Posts: 81
Likes: 0
From: Bismarck, ND. USA
I wanted a new motor. I don't know any rx8 owners that don't want new motors.
Reply
Old Aug 22, 2015 | 11:13 AM
  #239  
09Factor's Avatar
Original Turbo 'd Auto !!
 
Joined: Mar 2004
Posts: 2,136
Likes: 5
From: Surprise, Arizona
Originally Posted by TeamRX8


Remember my prior advice to STFU and wait for the final results? It was intended to help avoid the total clusterf-ck that this thread has become. The desire to look like a hero in advance is always too alluring. And of course the Scott-haters never miss their opportunity to sow doubt with the usual cheap shots that you so kindly keep setting up for them. There was also some discussion about proper financial planning, which when going turbo on a older daily driven engine means being prepared for the inevitable.

At this point the hole is so deep you might as well just keep posting/blabbing until you pop up in China.
Haha, Team. nicely put.

Originally Posted by BigBadChris
"Look like a hero in advance".....I have not bragged one time about what I am hoping to achieve. Instead, I am coming in here, reporting my progress, and asking for advice. Clearly that was too much to ask.

Please, give me some more financial advice. Did I say "Oh ****, I cant afford a rebuild, I am screwed!!!!!" No. I dont want to do a rebuild, no car owner does. We want the car to run, and we want to enjoy driving it. No one enjoys the idea of a damaged motor. I knew a rebuild was coming eventually, no RX8 lives forever. I was just hoping to get more time out of it.

China, here I come!
Big,

Reading over your entire thread, IMHO, the turbo is a little oversized for a 4port. Not wanting to rehash what has already been posted, I'll say this.. Fix the Coolant overflow drain line. Plumb it to the bottom of the radiator so it drains on the ground and not on the EPS connection.

As for your Fuel.
My injectors, > 2 stock red primaries. 2 Uncapped 880 Yellows (Series 1)
I can safely run 8psi with no worries, but i don't recall how much air is being feed to the motor. This nets me ~257 @ the wheels on a Dynapak Dyno. To run @ 10-12, yeah i need 1600cc's or better.

I don't recall what your injectors are at this point, but the devil is all in the tune.

Hope Scott pulls through for ya.

Last edited by 09Factor; Aug 22, 2015 at 11:17 AM.
Reply
Old Aug 28, 2015 | 10:03 AM
  #240  
BigBadChris's Avatar
Thread Starter
Registered
iTrader: (4)
 
Joined: Aug 2014
Posts: 680
Likes: 28
From: Dallas TX
A big thank you to 8club member Justin Fortz. He sold me a replica MS wing. The wing arrived last night, and I am very excited to get it mounted up once the car returns. We are planning to have it finished one week from today. I have also had some very interesting discussions with Ari, and he has some big plans for my little 4 port
Reply
Old Aug 28, 2015 | 11:05 AM
  #241  
shadycrew31's Avatar
WENTGERMAN
iTrader: (6)
 
Joined: Apr 2008
Posts: 5,806
Likes: 31
From: Burbs,PA
So, you bought a wing but might have a bad engine still?
Reply
Old Aug 28, 2015 | 12:49 PM
  #242  
BigBadChris's Avatar
Thread Starter
Registered
iTrader: (4)
 
Joined: Aug 2014
Posts: 680
Likes: 28
From: Dallas TX
I purhased the wing before I knew about the engine having a problem. The wing arrived, I unpacked it, and I was pleased with it. I wanted to publicly thank a member for giving me a good looking accessory at an excellent price.

The engine passed two coolant pressure tests and is running normally. Scott anticipates that the car will be completed on schedule.

If you think I am taking the engine/coolant issue lightly, I promise you I am not. I am aware that while low mileage (30k) it is still a nine year old engine. I plan on testing the car thoroughly when I get it back in my possession. I have a local rotary specialist who is a friend of mine. (I trust Scott, and he does good work, but I would rather pay $250 and run the tests again, to double check).

Last edited by BigBadChris; Aug 28, 2015 at 01:21 PM.
Reply
Old Aug 28, 2015 | 01:16 PM
  #243  
shadycrew31's Avatar
WENTGERMAN
iTrader: (6)
 
Joined: Apr 2008
Posts: 5,806
Likes: 31
From: Burbs,PA
Originally Posted by BigBadChris
I purhased the wing before I knew about the engine having a problem. The wing arrived, I unpacked it, and I was pleased with it. I wanted to publicly thank a member for giving me a good looking accessory at an excellent price.

The engine passed two coolant pressure tests and is running normally. Scott anticipates that the car will be completed on schedule.

If you think I am taking the engine/coolant issue lightly, I promise you I am not. I am aware that while low mileage (30k) it is still a nine year old engine. I plan on testing the car thoroughly when I get it back in my possession. I have a local rotary specialist who is a friend of mine. (I trust Scott, and he does good work, but I would rather pay $250 and run the tests again).
Thats excellent news, I thought you just went and bought a wing randomly.
Reply
Old Aug 28, 2015 | 01:54 PM
  #244  
Brettus's Avatar
Boosted Kiwi
iTrader: (2)
 
Joined: Apr 2006
Posts: 20,839
Likes: 1,796
From: Y-cat-o NZ
Great to hear the engine is ok . Bet you can't wait to get it back !

Last edited by Brettus; Aug 28, 2015 at 01:59 PM.
Reply
Old Sep 10, 2015 | 03:28 PM
  #245  
hoss -05's Avatar
Lucky #33
iTrader: (4)
 
Joined: Feb 2009
Posts: 2,851
Likes: 5
From: San Antonio, SARX Garage
Reply
Old Sep 10, 2015 | 04:27 PM
  #246  
BigBadChris's Avatar
Thread Starter
Registered
iTrader: (4)
 
Joined: Aug 2014
Posts: 680
Likes: 28
From: Dallas TX
Transport company absolutely hosed me. I was very confrontational on the phone, and now I think I need a new trucking company.

When it rains it pours

In the future, I will never ever use Car Transport Express. Useless customer service dept, poor communication, and they LEFT MY CAR IN A DIFFERENT STATE! They did not show up as promised on Saturday. Tuesday morning, I call the company. I speak to someone, they tell me the car has been picked up, on schedule for delivery Tuesday afternoon. I explain that isn't accurate. He insists, and connects me to the dispatcher. I explain my situation. The dispatcher tells me that they picked up the car. It wasn't until I sent them picture evidence did they contact the truck driver. 72 hours later, and I had to explain their mistake to them. No apology, no customer service.

Last edited by BigBadChris; Sep 11, 2015 at 10:19 AM.
Reply
Old Sep 10, 2015 | 05:02 PM
  #247  
RotaryMachineRx's Avatar
SPOOLN8
iTrader: (1)
 
Joined: Nov 2008
Posts: 2,300
Likes: 245
From: Edmonton, Alberta, Canada
^ So you do have the car back now?
Reply
Old Sep 10, 2015 | 05:29 PM
  #248  
BigBadChris's Avatar
Thread Starter
Registered
iTrader: (4)
 
Joined: Aug 2014
Posts: 680
Likes: 28
From: Dallas TX
Nope. They agreed to pick it up today. And guess what? They didn't show up. Again.
Reply
Old Sep 11, 2015 | 09:54 AM
  #249  
shadycrew31's Avatar
WENTGERMAN
iTrader: (6)
 
Joined: Apr 2008
Posts: 5,806
Likes: 31
From: Burbs,PA
Wow... That sucks man.
Reply
Old Sep 11, 2015 | 10:22 AM
  #250  
BigBadChris's Avatar
Thread Starter
Registered
iTrader: (4)
 
Joined: Aug 2014
Posts: 680
Likes: 28
From: Dallas TX
At this point, I could have pushed my car off a cliff, bought another one cash.....and still have been better off financially. Why do I do this to myself? Because I have wanted this car for more than a decade.
Reply


You have already rated this thread Rating: Thread Rating: 1 votes, 5.00 average.


All times are GMT -5. The time now is 06:50 PM.