Unorthodox Pulleys on Greddy Turbo
#1
Registered User
Thread Starter
Join Date: Feb 2004
Location: Toronto, Ontario
Posts: 331
Likes: 0
Received 0 Likes
on
0 Posts
Unorthodox Pulleys on Greddy Turbo
Just wanted feedback on what some of the experts on the board though about running Unorthodox Pulleys on a Greddy turbo setup. I believe the pulley setup under drives the water system by 15%. Is this an issue considernig that there is the added heat of the turbo setup? I am also running a PWR radiator.
Thoughts?
Thoughts?
#5
Registered User
Join Date: Nov 2003
Location: Glendale, CA
Posts: 3,281
Likes: 0
Received 0 Likes
on
0 Posts
NA. I tested the units (though mine are SR Motorsports). I tested them before I got the turbo, but I don't think they will make much more of a difference. This isn't like a supercharger where we are swapping out smaller drive pullies though, so hp gain is still minimal. Even on the turbo, my temperature is rock solid (no heat ups at all). PWR Radiator & Agency Power hose work fine. The problem that I have been running into is the O2 sensor & the heat associated with my cat is tripping my CEL to blink. I suppose I'll figure a way out of this as well.
Honestly, if I were you, i would save the money, and get a set of upgraded radiator hoses, or something else. Also, add some "water wetter." Stuff works. When I put in Royal Purple 5W-30 synthetic oil I could swear my temps dropped a bit. Maybe it's just in my head.
Honestly, if I were you, i would save the money, and get a set of upgraded radiator hoses, or something else. Also, add some "water wetter." Stuff works. When I put in Royal Purple 5W-30 synthetic oil I could swear my temps dropped a bit. Maybe it's just in my head.
#6
Registered User
Thread Starter
Join Date: Feb 2004
Location: Toronto, Ontario
Posts: 331
Likes: 0
Received 0 Likes
on
0 Posts
I already have the pulleys in hand... I just wanted to know if there were any issues in regards to taxing the cooling/water system. Thanks!
#9
Registered
Join Date: Feb 2006
Location: Conroe, Texas
Posts: 397
Likes: 0
Received 0 Likes
on
0 Posts
I've been debating underdrive pulleys for about a week now and it seems that the opinion on them is split, almost 50/50.
I was actually thinking about just the crank pulley and not swapping the water pump and alternator.
Any opinions out there?
I was actually thinking about just the crank pulley and not swapping the water pump and alternator.
Any opinions out there?
#10
Registered User
Join Date: Nov 2003
Location: Glendale, CA
Posts: 3,281
Likes: 0
Received 0 Likes
on
0 Posts
If you don't have them yet, I would not suggest getting them. Use the money and getings more vital to the the car, and that have shown to work better (hi-flow cat, gauges, air intake for NA car, etc.).
#11
Registered User
Join Date: Apr 2004
Location: Australia
Posts: 88
Likes: 0
Received 0 Likes
on
0 Posts
Nemesis8 , the eccentric pulley is the same as the crankshaft pulley right?
So with the UR pulley set only this pulley is underdriven, the other 2 are standard diameter.
Regards
Rexi
So with the UR pulley set only this pulley is underdriven, the other 2 are standard diameter.
Regards
Rexi
Thread
Thread Starter
Forum
Replies
Last Post
JimmyBlack
Series I Major Horsepower Upgrades
273
02-10-2020 10:23 PM