Calling all engine bays!
05-10-2013, 12:33 PM
#401
Banned
Join Date: Feb 2013
Location: State of insanity
Posts: 384
Likes: 0
Received 0 Likes
on
0 Posts
You might be disappointed because .....wait for it...... I bought a part from Summit racing. I hate to leave Home Depot racing because the parts are just soooo much cheaper
.
.
05-10-2013, 05:51 PM
#403
hey Chris, is that a cosmo motor?
or just 13BRE UIM, LIM and 20B TB etc etc
also heres mine.. whatever, it looks just like every other NA renny. I want to get the UIM plated like nemesis above..
old pic, and dont mind the electric tape.. my maf gasket was broken and needed a quick fix on the side of the road.
or just 13BRE UIM, LIM and 20B TB etc etc
also heres mine.. whatever, it looks just like every other NA renny. I want to get the UIM plated like nemesis above..
old pic, and dont mind the electric tape.. my maf gasket was broken and needed a quick fix on the side of the road.
05-10-2013, 08:34 PM
#404
Thanks, its actually polycarbonate, which starts to melt around 200 iirc.. so unless theres an engine fire its not going to deform.
V2 with 0 brackets is underway.
this tray costed about $60 in materials, but invaluable learning experience to make it better the second time around.
V2 with 0 brackets is underway.
this tray costed about $60 in materials, but invaluable learning experience to make it better the second time around.
05-11-2013, 06:18 AM
#405
Registered
Join Date: Jun 2012
Location: Poland, Wrocław
Posts: 41
Likes: 0
Received 0 Likes
on
0 Posts
05-13-2013, 12:03 PM
#406
hey Chris, is that a cosmo motor?
or just 13BRE UIM, LIM and 20B TB etc etc
also heres mine.. whatever, it looks just like every other NA renny. I want to get the UIM plated like nemesis above..
old pic, and dont mind the electric tape.. my maf gasket was broken and needed a quick fix on the side of the road.
or just 13BRE UIM, LIM and 20B TB etc etc
also heres mine.. whatever, it looks just like every other NA renny. I want to get the UIM plated like nemesis above..
old pic, and dont mind the electric tape.. my maf gasket was broken and needed a quick fix on the side of the road.
C
06-04-2013, 01:22 PM
#411
Banned
Join Date: Feb 2013
Location: State of insanity
Posts: 384
Likes: 0
Received 0 Likes
on
0 Posts
Probably because I was red faced over it. It was indeed dumb to post ,
, but hey it is a learning curve. I really don't care if the pic is up here. I will post another of the engine bay as soon as I can get the sticky duct tape off
. So to answer your question that's why
07-24-2013, 12:08 PM
#414
Cardboard.
lol jk, modeled it with cardboard, then used https://www.onlinemetals.com/merchan...id=7125&step=4
I'll upload a better pic when i get home
lol jk, modeled it with cardboard, then used https://www.onlinemetals.com/merchan...id=7125&step=4
I'll upload a better pic when i get home
07-24-2013, 02:44 PM
#421
. I have a brief section on it here: Normalexception.net - 2009 - 2011 RX8 Battery RelocationBut that needs to be updated as I now have just the hot wire running to the engine bay through a hole in the passenger side firewall, and the ground is just going to a bolt that mounts the rear seat (short wire).
My new setup is a bit different
