Notices
RX-8 Discussion General discussion about the RX-8 that doesn't fit in one of the specialty forums.

Charging for taillight replacement? Wtf?

Thread Tools
 
Search this Thread
 
Rate Thread
 
Old 04-28-2007, 12:06 PM
  #26  
Taylor not Tyler
Thread Starter
 
Mortal Moxie's Avatar
 
Join Date: Jul 2006
Location: Bristol, Connecticut
Posts: 188
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by dannobre
It is fused together...you can't reliably open them. It is possible to heat them and seperate the seams...but it is hit and miss. If it can't be cleaned from the bulb holes.....and it bothers you...get new ones

Ok.

I'm also gonna seat if I can just heat the assembly with a blow dryer to dry as much out of there as I can.

Thanks!
Old 04-28-2007, 12:11 PM
  #27  
Modulated Moderator
iTrader: (3)
 
dannobre's Avatar
 
Join Date: Feb 2004
Location: Smallville
Posts: 13,718
Received 334 Likes on 289 Posts
caeful not to get them too hot. If you read the tailight TSB on Rosenthals site they say to use no heat...ie on cold to dry them out.....
Old 04-28-2007, 01:08 PM
  #28  
Taylor not Tyler
Thread Starter
 
Mortal Moxie's Avatar
 
Join Date: Jul 2006
Location: Bristol, Connecticut
Posts: 188
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by dannobre
caeful not to get them too hot. If you read the tailight TSB on Rosenthals site they say to use no heat...ie on cold to dry them out.....
I gave up on the blow dryer idea as it seemed to just heat up the water inside the light and cause more steam, aka condensation.

I did find something else that completely fixed the condensation for me, so I added my little work instrucion to nycgps's DIY for tailight condensation.

Check it out.


https://www.rx8club.com/showthread.p...=1#post1854106
Old 04-28-2007, 06:33 PM
  #29  
Out of NYC
iTrader: (1)
 
nycgps's Avatar
 
Join Date: Jun 2005
Location: Planet Earth
Posts: 19,881
Received 32 Likes on 30 Posts
I replied ya pm.

just in case someone missed my DIY , do NOT use heat on the gasket, that crap melts easily, dont ask me how I know :P

blow dry it with room temp air.

or leave it on a stack of newspaper.

Most dealerships dont have bodyshops, they out source them most of the time. but if they're the ones who did your work, they should cover it.
Old 04-28-2007, 06:44 PM
  #30  
PoloRican Rotary
 
cas2themoe's Avatar
 
Join Date: Feb 2004
Location: Maryland
Posts: 1,501
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by Mortal Moxie
About a month ago my rear passenger qtr got smacked up in an accident. They had to replace the right tailight as a part of the repair.

The taillight that they put in is now full of water and has major condensation inside it.

Today I went to Mazda in my town to have them replace it, and the guy said that he would have to order a part and that they would check my light out. He said he might have to charge me to replace it.

Umm... why?

I told him there were service bulletins on the issue, and that Mazda should no longer be putting these faulty lights into RX8's. He said service bulletins are tech reports for Mazda techs and no customer should pay attention to them.

Anyone have to pay to get Mazda's crappy taillight replaced?
I've had my font, back and fog lights all replaced because of the condensation getting inside. My dealership did all of them for FREE. That should be under warranty. You didnt cause that!
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
New Yorker
RX-8 Discussion
40
03-22-2022 06:01 AM
TeslaMSI
New Member Forum
11
12-10-2015 01:10 AM
TJSiegrist
New Member Forum
9
09-10-2015 09:29 AM
GrAfiX
Series I Tech Garage
4
08-24-2015 08:08 AM
Belalnabi
New Member Forum
9
07-17-2015 07:48 PM



You have already rated this thread Rating: Thread Rating: 0 votes,  average.

Quick Reply: Charging for taillight replacement? Wtf?



All times are GMT -5. The time now is 03:28 AM.