Notices
Purchasing, Financing, & Insurance Talk about dealerships, your order status, delivery experience, ordering options, financing/leasing, insurance deals, etc.

What to look for in a used rotary.

Thread Tools
 
Search this Thread
 
Rate Thread
 
Old 05-24-2010, 07:31 PM
  #1  
Registered User
Thread Starter
 
Ravepuppie's Avatar
 
Join Date: May 2010
Posts: 1
Likes: 0
Received 0 Likes on 0 Posts
What to look for in a used rotary.

Hey all. I'm looking at a used 2004 RX8, 82K, MT, pretty much loaded with all the options. Red with black/red leather interior. Body is clean with no rust but a couple minor door dings. Interior is clean and shows surprisingly little wear, even on that lefthand driver's seat spot that usually wears on the side lumbar. Anyway, the guy is only asking $8900 for it which is below book by far. The only thing that bothers me is that there is what looks to be an aftermarket painted stripe that consists of black that fills in the triangle shape on the hood and continues the same width over the roof and down the trunk and bumper. I looked close and it just doesn't look factory but I've seen somewhat similar looking accents on some of the pics on this site. Sure, the shift **** is also a bit worn but the boot is fine with no tears. My ultimate question is simple: When going up to drive thing, what should I really be watching for? What are the signs of something bad to come? I used to have a 93 RX7 Touring and loved it...right up to the point where a cheap plastic fitting that fed coolant to the heater core cracked and spewed my precious fluid all over the highway. While trying to find what was making that chiming noise I noticed my engine temp was maxed out. I immediately stopped and shut it down and it never started again. I was really disappointed to see that it would be thousands to get a new engine and I had no desire to drop another engine for replacement. I'm looking for those little things that point to something on the horizon like a FUBAR cat, seal or ignition coil failure etc. Any tips would be appreciated. Thanks.
Old 05-24-2010, 07:51 PM
  #2  
Mil-spec wiring/elec!
 
JordanInnovations's Avatar
 
Join Date: May 2010
Location: 626, Socal.
Posts: 7
Likes: 0
Received 0 Likes on 0 Posts
I'd look for an LSx V8.

Sorry lol, I had to.
Old 05-25-2010, 06:44 PM
  #3  
Recovering Lurk-aholic
 
Nouvellion's Avatar
 
Join Date: Nov 2008
Location: Richfield, MN
Posts: 56
Likes: 0
Received 0 Likes on 0 Posts
Find the nicest, newest 8 available in your area and drive that one first for a reference point.

Watch for solid power in mid-upper RPMs, check if it starts easily when warm/hot, get a compression test done on the engine before you make the deal.

Ask for the maintenance history, or just what the guy does to take care of his car. make sure that's in line with what you know about rotaries from your 7 and from reading here.

There's only 18k left on that car's engine warranty. Make sure that's something you're going to be able to deal with.

There are plenty of other threads detailing more on what to look for Search button is your friend.
Old 05-25-2010, 11:46 PM
  #4  
kjb
Registered
 
kjb's Avatar
 
Join Date: May 2010
Posts: 116
Likes: 0
Received 0 Likes on 0 Posts
I also had an RX-7 (86) and recently bought an RX-8 on eBay. I don't have the 8 yet. I looked at the Carfax for it and found frequent maintenance. Obviously a meticulously owner maintained car won't show that, but might be better. At least the maintenance on this car was documented, so there is a record.

I'll report how the eBay experiment works out.
Old 05-26-2010, 12:28 AM
  #5  
U-Stink-But-I-♥-U
iTrader: (1)
 
carbonRX8's Avatar
 
Join Date: Mar 2005
Location: 12 o'clock on the Beltway.
Posts: 2,004
Likes: 0
Received 1 Like on 1 Post
Make sure no oil is leaking around the valve covers...
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
UHATEIT
Series I Trouble Shooting
11
03-31-2019 05:31 PM
garryg
Australia/New Zealand Forum
2
10-01-2015 04:54 PM
Ajmurphy85
New Member Forum
3
07-30-2015 07:51 AM
Astor
General Automotive
5
04-26-2004 09:32 AM



You have already rated this thread Rating: Thread Rating: 0 votes,  average.

Quick Reply: What to look for in a used rotary.



All times are GMT -5. The time now is 01:47 PM.