High positive fuel trims, low maf grams at idle
#26
Registered
Thread Starter
I am still trying to figure everything out, maybe it is normal I don't know. Another guy out here who has an rx8 says his fuel trim is always at about 20 long term with short term around 5 or 6. So either we both have issues or it is normal for vegas?
I just learned that I guess the 2009 rx8s do not have the extra engine warranty at least according to the dealer I called. Also my powertrain warranty ended on 9/2013 which kind of sucks as I now have a transmission leak that has been there a while but I only just noticed. The news just keeps getting worse lol.
I just learned that I guess the 2009 rx8s do not have the extra engine warranty at least according to the dealer I called. Also my powertrain warranty ended on 9/2013 which kind of sucks as I now have a transmission leak that has been there a while but I only just noticed. The news just keeps getting worse lol.
#28
Registered
iTrader: (15)
Originally Posted by myMazda.com
RX-8 Rotary Engine Core Limited Warranty Extension
Mazda Motor Corporation is extending the warranty coverage on Rotary Engine Core Components on all RX-8 vehicles produced after the 2004 model year. The warranty coverage for the Rotary Engine Core Components is extended to 8 years (96 months) from the original warranty start date, with a 100,000 mileage limitation.
Mazda Motor Corporation is extending the warranty coverage on Rotary Engine Core Components on all RX-8 vehicles produced after the 2004 model year. The warranty coverage for the Rotary Engine Core Components is extended to 8 years (96 months) from the original warranty start date, with a 100,000 mileage limitation.
#29
Boosted Kiwi
iTrader: (2)
I remember another member here with a turbo setup chasing a low maf reading for years , he never did get to the bottom of it . After changing , sensors , maf tubes and even engines he was still at a loss.
Last edited by Brettus; 01-13-2014 at 02:25 PM.
#35
SARX Legend
iTrader: (46)
I had the leaky clunky ssv actuator issue. Unfortunately I have fixed a few annoying vacuum leaks over the years.
Op, just make your own. I use this:
RX-8 Hymee Supercharger Install - Smoke Tester
Posted From RX8Club.com Android App
Op, just make your own. I use this:
RX-8 Hymee Supercharger Install - Smoke Tester
Posted From RX8Club.com Android App
#36
2009 RX-8 Touring
I'm sure it's already been said, but the simplest answer is the MAF is failing or dirty, and it's reading low, so the fuel trims have to be adjusted upward to compensate for the larger real air-mass going into the engine.
#38
SSV, VDI, and VFAD issues might be at play as well as the tune. Ordered new ones after testing and all failed, but similar problems were present when took to dealer and mechanics and "fixed". If tune was optimum (with communication to/from solenoids) and timing was advanced (probably around -15 to -20 and slightly rich the OEM solenoid design would likely be optimum. Thought of circumventing solenoids by splitting intake vacuum directly to both manifold actuators and adding electric and/or non-electric assisted velocity fans before and after MAF to increase air flow (correcting a resulting sloped torque curve instead of the advertised relatively flat optimum torque between 4,000 & 8,000 RPM due to simultaneous activator function) and encouraging system to make fuel mixture richer (with increased velocity before MAF), and circumventing VFAD and purge with vacuum from one of the ports to the "high rise" port of the manifold and making sure any resulting open lines were capped. You also may want to check PCVs as mine were completely clogged.
#40
Smoking turbo yay
Is there even a PCV on our Series 2? If so, is it called something different?
#41
Something that seemed to be "circulating around ('pun' intended)", it might be a good idea to use a check valve if running vacuum off the ports that the air, VDI, and SSV solenoids attach and it is possible the solenoids wouldn't need to be replaced if there were check valves going into them.
#42
What am I doing here?
Join Date: Mar 2006
Location: 2017 Miata RF Launch Edition
Posts: 3,606
Received 649 Likes
on
510 Posts
You bumped a long-dead thread with some oddball word salad. Then add another reply. Then quote yourself while ignoring another reply...
Are you just a bot having a conversation with itself?
Are you just a bot having a conversation with itself?
#43
Smoking turbo yay
Just in case anyone is curious...
Series 2(and from what I have searched, Series 1 as well) RX-8 doesn't have a PCV valve. The system is literally just the rubber hose that connects the oil filler neck to the intake accordion.
Series 2(and from what I have searched, Series 1 as well) RX-8 doesn't have a PCV valve. The system is literally just the rubber hose that connects the oil filler neck to the intake accordion.
#45
Something that seemed to be "circulating around ('pun' intended)", it might be a good idea to use a check valve if running vacuum off the ports that the air, VDI, and SSV solenoids attach and it is possible the solenoids wouldn't need to be replaced if there were check valves going into them.
#46
Dates seemed recent. Later posts didn't seem directly related although replies to "self" seem relevant to context if others are arguing situation for optimum performance at time.
Thread
Thread Starter
Forum
Replies
Last Post
Kane
Series I Engine Tuning Forum
249
04-08-2024 01:16 PM