Will It Fit Thread
Registered
iTrader: (2)
Yes the wheel studs did extend past the spacer but the pocket in the back of the OEM R3 wheel
was deep enough to allow the extra lenght so everything fit perfect.
I used Eibach pro spacer/hub center,and painted them flat back.
was deep enough to allow the extra lenght so everything fit perfect.
I used Eibach pro spacer/hub center,and painted them flat back.
Good Morning Gremlin!
iTrader: (2)
Join Date: May 2009
Location: Petawawa and Ottawa
Posts: 218
Likes: 0
Received 0 Likes
on
0 Posts
Buying this month!
I'm looking at Enkei RPF1s
9.5x19 w/ 42 offset
265/30 R19
OR
275/30 R19
Fenders are rolled already and I have BC Coils so I just want to know if this will be flush and if it will have issues..
Thanks!
9.5x19 w/ 42 offset
265/30 R19
OR
275/30 R19
Fenders are rolled already and I have BC Coils so I just want to know if this will be flush and if it will have issues..
Thanks!
To give you an Idea.. Im running. 19x9.5 245/35R19 + 12 in the rear and + 22 in the front. Needed to roll my fenders and adj. my camber. I was able to fit 275/30R19 and 285/30R19 that was +35 if I remember in the rears on my last RX8 i did 25535R19 in the front though.. you can probably fit 265/30 in the front im thinking with that offset and width..
RIP Furai
iTrader: (3)
265/30s on 19x9.5 +43 rub the rear fenders if they aren't rolled, but you should be good if you're rolled. I can't comment on the front or how low you can go though.
Legend In My Own Mind
How about:
245/40/R18's
18 x 9.5" rims, +45 offset
25mm Garageline Spacers
1.4" drop in front
0.7" drop in rear (TEIN S-Tech Springs)
245/40/R18's
18 x 9.5" rims, +45 offset
25mm Garageline Spacers
1.4" drop in front
0.7" drop in rear (TEIN S-Tech Springs)
Registered
Awesome, thanks... I already bought a small metal baseball bat and did the fender-rolling with the bat wrapped in soft cloth to prevent scratching, but how did you deal with those tabs that are part of the rear bumper?
Legend In My Own Mind
If it is close you may be able to get away with bending them upward a bit, but otherwise you will need to break out a cutoff wheel and trim things a bit. That thing is sharp and will noticeably get into your tire.
Can anyone help me out.. ive done a bit of research but im still not 100% sure it im going to have fitment issues..
Can I fix 18x10 +15 on a 235/40 tyre?
Apparently you can with -1.3 camber but I dont know if I need to roll? Or whats the go if I want to drop it on stance coilovers?
Can I fix 18x10 +15 on a 235/40 tyre?
Apparently you can with -1.3 camber but I dont know if I need to roll? Or whats the go if I want to drop it on stance coilovers?
HELP! Will these wheels fit my rx8?
19"faulken rims with tires
back tires extreme zr, 275/35/zr19. Front 245/35/zr19. Chrome 19" faulken rim
with 5 bolt pattern.
back tires extreme zr, 275/35/zr19. Front 245/35/zr19. Chrome 19" faulken rim
with 5 bolt pattern.
Pew Pew Pew
iTrader: (10)
19"faulken rims with tires back tires extreme zr, 275/35/zr19. Front 245/35/zr19. Chrome 19" faulken rim with 5 bolt pattern.
Pew Pew Pew
iTrader: (10)
Can anyone help me out.. ive done a bit of research but im still not 100% sure it im going to have fitment issues.. Can I fix 18x10 +15 on a 235/40 tyre? Apparently you can with -1.3 camber but I dont know if I need to roll? Or whats the go if I want to drop it on stance coilovers?
Legend In My Own Mind
Registered
iTrader: (1)
I have been looking at a set of Momo Revenge wheels for my 8. They are 18x8, offset is 40. Bolt Pattern is 5x114.3. So looking at the wheel guide it should fit however I've plugged it into 2 different sites and they say it doesn't fit for some reason. I don't know what the center bore is but generally aftermarket wheels have an over sized one with the locking ring ( I think that's what it's called but I can't remember for sure). Does anyone have any ideas?
Last edited by Dustintomi; 06-04-2014 at 01:06 PM.
Pew Pew Pew
iTrader: (10)
I have been looking at a set of Momo Revenge wheels for my 8. They are 18x8, offset is 40. Bolt Pattern is 5x114.3. So looking at the wheel guide it should fit however I've plugged it into 2 different sites and they say it doesn't fit for some reason. I don't know what the center bore is but generally aftermarket wheels have an over sized one with the locking ring ( I think that's what it's called but I can't remember for sure). Does anyone have any ideas?