WDS and DLC-2
#1
WDS and DLC-2
I need the WDS tool for my 8, need quite a bit of configuring to do with my 8. I have found a tool, Ford VCM IDS (VCM)...I was wondering if anyone has had any luck with this? I would take my 8 to the stealership, but I don't have the money. I'm more of a DIY kinda guy.
#6
The Mazda NGS won't communicate with the RX-8 Can Bus though. The WDS was replaced by the IDS.
What exactly do you need done on your RX-8? There are some ways around it through the aftermarket, depending on your budget.
What exactly do you need done on your RX-8? There are some ways around it through the aftermarket, depending on your budget.
#10
I just checked and it does not look like you can program the power steering module using an aftermarket passthru device. Only PCMs. So it sounds like the dealership will be the only way for you on the power steering module.
Here's some info for you here on independent Mazda access:
https://www.mazdaserviceinfo.com/Default.aspx
You can use the IDS & a PC but you will need the Mazda software and access to their dealer website....maybe you have some Mazda connections?
Last edited by jrx13; 10-14-2011 at 12:01 PM.
#12
So if I buy a subscription of the mazda service info site for ecu programming, and buy an IDS Ford/Mazda module, I can program my car correct? And all of my airbags are fine, I don't understand why it's flashing the airbag code. It flashes twice, pauses, flashes 3 times, pauses, and then flashes 2 times again. It does that for a couple of rounds and then just stays solid. The car was originally rear ended, and I fixed it up. The airbag light was there when I got this rx8. All airbags are fine though!/: Is there anything I could check?
#13
Administrator
well you have the whoel sytem of sensors. maybe one of the crash sensors is not plugged in right after the rear was fixed. or maybe the connector is damaged or maybe... or maybe....
by programming do you mean tune? if so then no the IDS can not tune the car. it can help you with everything else as far as diagnostic and CAN module replacement etc but not tuning.
by programming do you mean tune? if so then no the IDS can not tune the car. it can help you with everything else as far as diagnostic and CAN module replacement etc but not tuning.
#15
Ok if you have an IDS and the required cables, you MUST also have the Mazda software installed onto your PC. You can then check codes and perform certain tests and functions with just that.
If you want to do a transfer of information from one module to a replacement module you will be able to do that as well. For instance you are replacing your EPS module, you will access the old EPS module with the scan tool and download the configuration file to the scan tool/PC. You will then replace the EPS in the car with a blank EPS and upload your old config file with the scan tool.
If you can't get your old info out due to a messed up module or don't have a config file to upload to the scan tool/PC, you will need Mazda's website access to download the config file you require off of their protected servers.
Do you really need to do any of this?
As far as your air bag light. It is flashing code #23 according to your post. You can do a search for air bag code #23.
And if you want to pull out your instrument cluster and replace a bulb, you can do that as well. No reprogramming necessary. Are you sure it is an LED not a regular bulb? If it is an LED it probably is soldered on.
If you want to do a transfer of information from one module to a replacement module you will be able to do that as well. For instance you are replacing your EPS module, you will access the old EPS module with the scan tool and download the configuration file to the scan tool/PC. You will then replace the EPS in the car with a blank EPS and upload your old config file with the scan tool.
If you can't get your old info out due to a messed up module or don't have a config file to upload to the scan tool/PC, you will need Mazda's website access to download the config file you require off of their protected servers.
Do you really need to do any of this?
As far as your air bag light. It is flashing code #23 according to your post. You can do a search for air bag code #23.
And if you want to pull out your instrument cluster and replace a bulb, you can do that as well. No reprogramming necessary. Are you sure it is an LED not a regular bulb? If it is an LED it probably is soldered on.
Last edited by jrx13; 10-20-2011 at 01:47 PM.
#16
weeeeeeeeee
iTrader: (12)
Thread resurrection --- can someone out there post the RX-8 compatible Mazda IDS version # (if versioning matters) and the model # of the VCM they're using?
Would appreciate it!
Shell
Would appreciate it!
Shell
Thread
Thread Starter
Forum
Replies
Last Post
fwb
Series I Interior, Audio, and Electronics
2
12-07-2011 11:17 AM
BBQdDude
Series I Interior, Audio, and Electronics
2
12-21-2008 11:01 AM