some more on the oil froth
#28
Modulated Moderator
iTrader: (3)
Froth is water vapor.....hot oil boils it off........
Short trips = cool oil and more condensation = more froth
Long trips = warmer oil and less condensation = less froth
Drive the **** out of it = no problem
The 04-05's were the worst till they fixed the breather...now they aren't bad
Oil and coolant temp control are important....hard to keep them cool in the summer stock...and hard to keep them warm in the winter...
Short trips = cool oil and more condensation = more froth
Long trips = warmer oil and less condensation = less froth
Drive the **** out of it = no problem
The 04-05's were the worst till they fixed the breather...now they aren't bad
Oil and coolant temp control are important....hard to keep them cool in the summer stock...and hard to keep them warm in the winter...
#33
Nature vs. Nurture
iTrader: (5)
Join Date: Oct 2009
Location: Maple Grove, MN
Posts: 382
Likes: 0
Received 0 Likes
on
0 Posts
Here is what driving it took to get rid of froth on a 21 degree F day: I drove 2 three hour drives yesterday at 70 mph. It wasn't all gone when I got home.
Today I had a friend with an Ipod measure the Gs thru 2nd and 3rd. To slow things down, I found a huge hill and did 4 pulls to redline in 2nd and 3rd. The froth was gone.
Sadly i can't do the second every day. How hard is it to upgrade the breather? I have read one TSB that involves unbolting parts underneath the oil filler and adding vacuum lines. Is adding a catch can just as good?
Today I had a friend with an Ipod measure the Gs thru 2nd and 3rd. To slow things down, I found a huge hill and did 4 pulls to redline in 2nd and 3rd. The froth was gone.
Sadly i can't do the second every day. How hard is it to upgrade the breather? I have read one TSB that involves unbolting parts underneath the oil filler and adding vacuum lines. Is adding a catch can just as good?
#36
Update
Yesterday I checked the oil and it was clean excpet around the rubber top of the dip stick there was a very minor bit of froth. Today I checked again and basically had the same results. I still have vaccum from the intake to the oil filler neck. I will be removing the driver oil cooler block and leaving the hose connected to the intake today*did it already*. If the froth doesn't go too crazy then I'll remove the filler hose and replace it with a cheap 2" breather and see how that goes. Ither way i'll try both just depends on how fast the froth builds as to which route I take.
Yesterday I checked the oil and it was clean excpet around the rubber top of the dip stick there was a very minor bit of froth. Today I checked again and basically had the same results. I still have vaccum from the intake to the oil filler neck. I will be removing the driver oil cooler block and leaving the hose connected to the intake today*did it already*. If the froth doesn't go too crazy then I'll remove the filler hose and replace it with a cheap 2" breather and see how that goes. Ither way i'll try both just depends on how fast the froth builds as to which route I take.
Last edited by Mr.&Mrs.Magic; 12-30-2009 at 01:57 PM.
#38
Ya know this makes me wonder a few things. If my oil pan is full of this smutz what problems might that cause considering engine life. The froth is basically created from *water* right? So what kind of corresion might that be causing over extened time periods. How about the OMP is it possible it might be picking up some of this foam and injecting a bit less oil due to the mass/volume/weight difference of the frothy oil vs. pure oil. Also how about the oil filter could some of this froth block it's ability to filter in any way?
Last edited by Mr.&Mrs.Magic; 12-30-2009 at 02:57 PM.
#39
Life begins @ 30 psi
Join Date: Mar 2008
Location: Columbia, MD
Posts: 1,745
Likes: 0
Received 0 Likes
on
0 Posts
#40
Registered
iTrader: (3)
thats exactly the thoughts i was having concerning the 04 oil filter bypass pressure being too low.
if the oil cannot get through the oil filter and the by pass opens--then this stuff has a full run through the system.
on cold mornings i am thinking the oil filter by pass is being activated. to much pressure difference with the cold oil. cold oil does not flow well.
thats why i switched to the 09 oil filter with the higher bypass pressure.
mazda has a reason they switch things around.
BW---when i removed my pan --about 1/3 of it was covered with this stuff. that and my uoa caused me to change things around some.
if the oil cannot get through the oil filter and the by pass opens--then this stuff has a full run through the system.
on cold mornings i am thinking the oil filter by pass is being activated. to much pressure difference with the cold oil. cold oil does not flow well.
thats why i switched to the 09 oil filter with the higher bypass pressure.
mazda has a reason they switch things around.
BW---when i removed my pan --about 1/3 of it was covered with this stuff. that and my uoa caused me to change things around some.
#41
OD what exactly do you mean you switched to the 09 filter? Is it just the filter itself that's different or is there something different in the filter mount. I rember some saying were using a larger miata spec filter but it was to big when running the RB oil plate.
#42
Nature vs. Nurture
iTrader: (5)
Join Date: Oct 2009
Location: Maple Grove, MN
Posts: 382
Likes: 0
Received 0 Likes
on
0 Posts
The '09 filter is a bit taller than the one for our cars, but the difference is a higher bypass pressure. That is, if the oil is cold and viscous, it won't bypass the filtering potion of the oil filter as easily.
#43
new results
Car has had 6 startups with approx 15-20 min of inital idle time. Ambient temps have been 32 or less since monday and that's the first time I have driven since removing the oil cooler blocking plate. I haven't seen the water temp over 176 and oil will not go over 170 in normal driving conditions. I have also noticed that with the mazmart t-stat installed as soon as the radiator gets to 176 the t-stat will open and temps fall to approx 168 before rising again to 176. This all takes place in about 1 minute for a complete open to open cycle. Temps fall fast and recover in about 45 sec. I didn't really expect to see this much froth back in the oil pan after just 6 drive cycles but my car is also struggling to get near operating range unlike most rx-8's. It is looking to me as if the BHR rad and Mazmart t-stat are a bad combination for a NA winter driven rx-8. I'm going to install the block again and see how long it take to go away then i'll remove it again and also remove the oil filler neck hose as well adding a filter to atmosphere and see what results that may yield.
sorry crappy cell phone pics again
sorry crappy cell phone pics again
#48
Registered
iTrader: (3)
ok relax folks---the coolant temps are not that important here. mazmarts setup is fine.
Matter of fact a well known company is considering manufactoring a well made oil cooler blocker pop in.
You will get much better results if you block both coolers all the way out to level with the fog lights. Use that thick of foam. Just blocking the cooler with a flexable thin thing doesnt work as well as some airflow will continue to get by when you are at speed.
Even on a 26F morning now i can get mine up to 180 on the interstate and 195-200 in town. Coolant temps will also go up a little maybe 10-15 degrees.
Oil cooler blocks could be made to look really good
Matter of fact a well known company is considering manufactoring a well made oil cooler blocker pop in.
You will get much better results if you block both coolers all the way out to level with the fog lights. Use that thick of foam. Just blocking the cooler with a flexable thin thing doesnt work as well as some airflow will continue to get by when you are at speed.
Even on a 26F morning now i can get mine up to 180 on the interstate and 195-200 in town. Coolant temps will also go up a little maybe 10-15 degrees.
Oil cooler blocks could be made to look really good
#49
Registered
iTrader: (1)
Join Date: May 2006
Location: Carolina Beach, NC
Posts: 1,934
Likes: 0
Received 0 Likes
on
0 Posts
Thanks Denny, been wondering what to about this as of late. Can you post a pic of the oil cooler blocks you have installed? Just want to see how much I have to block...I don't have fogs installed.
#50
Registered
iTrader: (3)
you know my rep concerning pics!
No fogs then just level with the opening?
details of what I did:
1- used a small piece of heat shield on the front side of the coolers
2- fairly thick piece of home depo type insulating foam (cut to desired size) on top of that
3- piece of a left over track magnetic number sign I had lying around on top of the foam
4- lock it down with the long plastic through fasteners like you get with a additional cooler kit. you can get these separate at most any auto parts store.
Actually I have only mentioned this to Paul at Mazmart as an item they may want to make for sell and just a "plug int type". If the package was shaped well and have the right type of anchor all you would have to do is to push them in when the weather got cooler. They could be made to look really good and have personnalized message on them like " TOO COOL"
or something.
OD
No fogs then just level with the opening?
details of what I did:
1- used a small piece of heat shield on the front side of the coolers
2- fairly thick piece of home depo type insulating foam (cut to desired size) on top of that
3- piece of a left over track magnetic number sign I had lying around on top of the foam
4- lock it down with the long plastic through fasteners like you get with a additional cooler kit. you can get these separate at most any auto parts store.
Actually I have only mentioned this to Paul at Mazmart as an item they may want to make for sell and just a "plug int type". If the package was shaped well and have the right type of anchor all you would have to do is to push them in when the weather got cooler. They could be made to look really good and have personnalized message on them like " TOO COOL"
or something.
OD