Limp mode with Seafoam?
#1
Yeay Boosted!
Thread Starter
Join Date: Oct 2007
Location: New Hampshire
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
Limp mode with Seafoam?
So, My car was running fine. no problems, no cells. all is good.
I just cleaned my car with seafoam. Removed all the sensors. Removed nipples, cranked some seafoam into the chambers. wait an hour. car starts, kinda choky rough idle (I assume because of the seafoam) let idle for a few minutes, White smoke puffing out exhaust. wonderful seafoam smell. while it's idling, It throws a cell, (which I thought might happen) well, I went to go and rev it up, and it won't rev past 2500 rps. I assume it's stuck in limp mode... Smoke starts to dissapate. idle starts to get better..
Car is still in limp mode.
So, the question is, how do I get it out?
Mabey I dislogged the Mother chunk of carbon buildup into my engine.. neigh the king of chunks.. the ruler of all chunk kind!
and my engine shed a single, lonly tear.
I just cleaned my car with seafoam. Removed all the sensors. Removed nipples, cranked some seafoam into the chambers. wait an hour. car starts, kinda choky rough idle (I assume because of the seafoam) let idle for a few minutes, White smoke puffing out exhaust. wonderful seafoam smell. while it's idling, It throws a cell, (which I thought might happen) well, I went to go and rev it up, and it won't rev past 2500 rps. I assume it's stuck in limp mode... Smoke starts to dissapate. idle starts to get better..
Car is still in limp mode.
So, the question is, how do I get it out?
Mabey I dislogged the Mother chunk of carbon buildup into my engine.. neigh the king of chunks.. the ruler of all chunk kind!
and my engine shed a single, lonly tear.
Last edited by marcux; 08-04-2008 at 08:59 PM.
#3
Yeay Boosted!
Thread Starter
Join Date: Oct 2007
Location: New Hampshire
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
I let it rpm between 1000-2000 because it wouldn't go past 2000 when it warmed up since I put it in, it hasn't gone past 2000.
#6
bi polar rotor loner
seafoamed for an hour? I wouldn't of bothered. try at least 4 hour minimum or better yet, let it sit over night.
I always reset the nvram and kam at first start up.
never have a problem.
I always reset the nvram and kam at first start up.
never have a problem.
#7
Yeay Boosted!
Thread Starter
Join Date: Oct 2007
Location: New Hampshire
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
Ok, I found out what the problem is.. I think I inhaled too much seafoam..
I pulled a few fuses out fuel pump, atv and injector fuses so that It wouldn't be injecting fuel into the chamber instead of climbing to the botton and disconnecting the eshaft sensor.. well, I put one of the fuses into an empty slot.. I'll chock this one up under idiot. well limp mode went away. I got it to rev up.. but it's having a really rough time idling, if I don't keep gas pressed slightly, it'll stall out.
I pulled a few fuses out fuel pump, atv and injector fuses so that It wouldn't be injecting fuel into the chamber instead of climbing to the botton and disconnecting the eshaft sensor.. well, I put one of the fuses into an empty slot.. I'll chock this one up under idiot. well limp mode went away. I got it to rev up.. but it's having a really rough time idling, if I don't keep gas pressed slightly, it'll stall out.
Thread
Thread Starter
Forum
Replies
Last Post