Gasket between Cat Pipe and 'Middle Pipe'?
#1
Sydney, Australia
Thread Starter
Gasket between Cat Pipe and 'Middle Pipe'?
got some exhaust work on the schedule tomorrow so I'm wondering if anyone knows if there is a gasket between the Cat Pipe and 'Middle Pipe'. If so what type is it - a flat sheet metal type of those compressed O-ring shaped things. The manual shows nothing - a pic would be good!
cheers
Larry
cheers
Larry
#4
Sydney, Australia
Thread Starter
well the manual I have lists the Cat section (called TWC), then that joins to the 'Middle Pipe' as the manual calls it, then that joints to the 'Main Silencer' or rear muffler.
expo1 is this the thing? If its reusable I might wait to see if I can get away with that then.
expo1 is this the thing? If its reusable I might wait to see if I can get away with that then.
#5
on his 3rd rx8
iTrader: (3)
it goes
headers, midpipe (cat), muffler (exhaust)...theres only 2 pipes after the header
the cat(midpipe) is connected to the header, then the exhuast (mufflers) is connected to the cat (midpipe).
^that gasket goes from the end of the cat (mipipe) to the exhaust (muffler).
the other thinner gasket you saw on the webpage is for the header to cat (midpipe).
headers, midpipe (cat), muffler (exhaust)...theres only 2 pipes after the header
the cat(midpipe) is connected to the header, then the exhuast (mufflers) is connected to the cat (midpipe).
^that gasket goes from the end of the cat (mipipe) to the exhaust (muffler).
the other thinner gasket you saw on the webpage is for the header to cat (midpipe).
#6
Sydney, Australia
Thread Starter
Oh for COL - here - 3 pieces of pipe after the header if one also counts the muffler assembly as a pipe. The joint I'm concerned with is circled in RED...
#12
Registered Zoom Zoomer
iTrader: (2)
Fluid Motorsports has a high performance crush gasket for $22.
http://www.fluidmotorsports.com/imag...medium/777.jpg http://www.fluidmotorsports.com/p-93-exhaust.aspx
btw: in your picture note the two O2 sensors (SST); just info since many folks ask about them.
http://www.fluidmotorsports.com/imag...medium/777.jpg http://www.fluidmotorsports.com/p-93-exhaust.aspx
btw: in your picture note the two O2 sensors (SST); just info since many folks ask about them.
#13
Sydney, Australia
Thread Starter
Fluid Motorsports has a high performance crush gasket for $22.
http://www.fluidmotorsports.com/imag...medium/777.jpg http://www.fluidmotorsports.com/p-93-exhaust.aspx
btw: in your picture note the two O2 sensors (SST); just info since many folks ask about them.
http://www.fluidmotorsports.com/imag...medium/777.jpg http://www.fluidmotorsports.com/p-93-exhaust.aspx
btw: in your picture note the two O2 sensors (SST); just info since many folks ask about them.
#15
Sydney, Australia
Thread Starter
Okay its all done and the central gasket was indeed re-usable. 3 hours to get the old one off and 20 minutes to fit the new one (damn those rubber hangers!)
So I now have a single muffler Mazdaspeed Stainless Steel cat back fitted for the Grand total of $AUD178.00 - $40.50 for the unit itself - used previously for 1 hour - courtesy of Ebay - and $138.00 to courier the thing up from Melbourne.
Sounds great! Now looking forward to its first Track Day on Wednesday!
So I now have a single muffler Mazdaspeed Stainless Steel cat back fitted for the Grand total of $AUD178.00 - $40.50 for the unit itself - used previously for 1 hour - courtesy of Ebay - and $138.00 to courier the thing up from Melbourne.
Sounds great! Now looking forward to its first Track Day on Wednesday!
Last edited by SARRAS; 06-20-2009 at 05:48 AM.
Thread
Thread Starter
Forum
Replies
Last Post