Am I screwed or what?
#1
Greensboro's Finest
Thread Starter
Join Date: Jun 2007
Location: Greensboro, NC
Posts: 661
Likes: 0
Received 0 Likes
on
0 Posts
Am I screwed or what?
Basically, I took off the cover of my engine bay and found this broken hose in my intake. It looks like it's a broken base or attachment. I'm not quite sure what it goes to and I didn't see anything in my manual. I cranked it up and it makes a whine similar to a super charger.
I'm posting a pic
And, for the record, I searched "broken intake hose" but to no avail. Please help guys.
I'm posting a pic
And, for the record, I searched "broken intake hose" but to no avail. Please help guys.
#4
No respecter of malarkey
iTrader: (25)
I had one break and bought several to have as spares, to get me by I bought a universal one at a parts store, they didn't have an elbow in the right size so I used a straight one until the OE parts arrived
you're engine may run lean so be careful driving it like that
you're engine may run lean so be careful driving it like that
#6
Greensboro's Finest
Thread Starter
Join Date: Jun 2007
Location: Greensboro, NC
Posts: 661
Likes: 0
Received 0 Likes
on
0 Posts
Is it something I can do myself if I went to the parts store and did it? I wouldn't mind shelling out a little dough and doing it myself if the difficulty for this is minimal. Would I need any tools?
#10
Greensboro's Finest
Thread Starter
Join Date: Jun 2007
Location: Greensboro, NC
Posts: 661
Likes: 0
Received 0 Likes
on
0 Posts
If you all notice, the place where the hose is suppose to go into doesn't have a hole. It appears to be melted over... Or is it suppose to be like that?
#13
Greensboro's Finest
Thread Starter
Join Date: Jun 2007
Location: Greensboro, NC
Posts: 661
Likes: 0
Received 0 Likes
on
0 Posts
Yea, I bought it used with 28k from Carmax. So it seems like this could be done rather easy. Is there an exact name I should ask for this hose from a parts store?
#16
Greensboro's Finest
Thread Starter
Join Date: Jun 2007
Location: Greensboro, NC
Posts: 661
Likes: 0
Received 0 Likes
on
0 Posts
I went to the parts store and asked for a plastic T piece and they didn't know what I was talking about at all... even when I showed them (any surprises there?). Can anyone give me any more tips please before I go to the big D?
#17
The Professor
When you are asking for it, just say "vacuum hose 90 degree fitting made of plastic"
yeah, those auto parts guys are dumb.
I wouldnt drive the car too hard until you get that replaced, with that piece open it is messing up any number of systems that rely on a constant vacuum reading.
From the looks of that break, it is completely shattered, whoever broke that must have seriously abused something.
#18
The Professor
Yeah, its the metering oil pump vacuum hose.
For the record: your RX8 is not lubricating itself. Drive carefully.
its extremely easy to replace. With the right part it would take no more than five minutes to install. its just 1) pull out all broken pieces 2)push in new fitting
be very careful when you take out the broken pieces whatever falls into those holes goes right into the engine!
if any crumbs do happen to fall into the holes it would be worth your while to take the whole thing apart and fish them out. That section is pretty easy to remove/install since it isn't complcated.
For the record: your RX8 is not lubricating itself. Drive carefully.
its extremely easy to replace. With the right part it would take no more than five minutes to install. its just 1) pull out all broken pieces 2)push in new fitting
be very careful when you take out the broken pieces whatever falls into those holes goes right into the engine!
if any crumbs do happen to fall into the holes it would be worth your while to take the whole thing apart and fish them out. That section is pretty easy to remove/install since it isn't complcated.
Last edited by staticlag; 06-04-2007 at 12:16 AM.
#20
Greensboro's Finest
Thread Starter
Join Date: Jun 2007
Location: Greensboro, NC
Posts: 661
Likes: 0
Received 0 Likes
on
0 Posts
UPDATE: I went to the dealership City Motors Mazda here in Greensboro and how about the service manager told me that I needed a whole new "air tube"! He tried to say that that elbow is part of the big tube of the intake and I needed that and a brand new hose.... Then I showed it to the parts guy and he needed an elbow and then the service manager came out and corrected him. Feeling they were trying to dupe me, I went to advance auto up the street and they pulled it out for me and got me set up with an elbow. Can you believe that?
4 Dollar Fix ftw!
4 Dollar Fix ftw!
#21
Surf Hard, Drive Hard
Join Date: Feb 2007
Location: Indialantic, Florida
Posts: 7,840
Likes: 0
Received 11 Likes
on
9 Posts
UPDATE: I went to the dealership City Motors Mazda here in Greensboro and how about the service manager told me that I needed a whole new "air tube"! He tried to say that that elbow is part of the big tube of the intake and I needed that and a brand new hose.... Then I showed it to the parts guy and he needed an elbow and then the service manager came out and corrected him. Feeling they were trying to dupe me, I went to advance auto up the street and they pulled it out for me and got me set up with an elbow. Can you believe that?
4 Dollar Fix ftw!
4 Dollar Fix ftw!
#23
Greensboro's Finest
Thread Starter
Join Date: Jun 2007
Location: Greensboro, NC
Posts: 661
Likes: 0
Received 0 Likes
on
0 Posts
Yea, they wanted 8 bucks. I actually was giving them a shred of confidence but man oh man did they just nix that. Kinda sucks because I was planning on buying my next Mazda from them in a few months... Probably not now.
Thread
Thread Starter
Forum
Replies
Last Post
projectr13b
Series I Do It Yourself Forum
1
09-06-2015 01:04 PM
RAVSPEC
Vendor Classifieds
0
08-05-2015 02:53 PM