Greddy kit and AP
#1
HAVOC
Thread Starter
Join Date: Jun 2008
Location: Afghanistan
Posts: 800
Likes: 0
Received 0 Likes
on
0 Posts
Greddy kit and AP
Since the information is spread about 5 different threads with each 7 or more pages, perhaps an expert can write somthing up about greddy install with the AP in once place for everyone to reference.
Are the 3 greddy fixes needed?
How do you control the wastegate (or BOV if you get one)?
Is a new Intake nessicerry?
What are all the check valve install locations?
Are the 3 greddy fixes needed?
How do you control the wastegate (or BOV if you get one)?
Is a new Intake nessicerry?
What are all the check valve install locations?
Last edited by WingleBeast; 01-21-2009 at 10:59 PM.
#2
Rotary Powered Countryboy
ok I"m not FI but I'll give u what i know....
The Greddy fixes are not a MUST just a "recommendation"
What do you mean about controling the BOV? Do you mean when it "goes off" well that all depends on the amount of boost you are running....basically when ur in boost and let off gas(to shift) ur BOV will go off when ur still in "vacuum" then it will not do anything(like shift at 2k rpms or something)
A new intake? well when u get the kit a "hot air" is provided where the filter is just sitting wher the stock airbox is located now...many ppl aroound here put a custom CAI in the car usually AEM or Mazdaspeed(same thing) is their "base" starting intake!
(anything I may be incorrect on for all u other FI guys please correct me I'm still learning)
The Greddy fixes are not a MUST just a "recommendation"
What do you mean about controling the BOV? Do you mean when it "goes off" well that all depends on the amount of boost you are running....basically when ur in boost and let off gas(to shift) ur BOV will go off when ur still in "vacuum" then it will not do anything(like shift at 2k rpms or something)
A new intake? well when u get the kit a "hot air" is provided where the filter is just sitting wher the stock airbox is located now...many ppl aroound here put a custom CAI in the car usually AEM or Mazdaspeed(same thing) is their "base" starting intake!
(anything I may be incorrect on for all u other FI guys please correct me I'm still learning)
#4
Rotary Powered Countryboy
^ok so I had it down(was not really sure about the check valve) I knew the BOV were run on vacuum lines but was a littel confused of wheat he was looking for!
#7
Pull My Finger
iTrader: (7)
Greddy Turbo Fixes sticky:
https://www.rx8club.com/series-i-major-horsepower-upgrades-93/definitive-greddy-turbo-fixes-here-they-81825/
be sure to read carefully like kane mentioned alot of it has to do with issues that where related to the emanage blue & ultimate other
than fix #2
https://www.rx8club.com/series-i-major-horsepower-upgrades-93/definitive-greddy-turbo-fixes-here-they-81825/
be sure to read carefully like kane mentioned alot of it has to do with issues that where related to the emanage blue & ultimate other
than fix #2
#9
Nope
iTrader: (9)
Not to mention the filter is unshielded inside the engine bay and heat soaks very quickly, you can see some very high IAT's in the summer.
Thread
Thread Starter
Forum
Replies
Last Post
TotalAutoPerformance
Vendor Classifieds
12
10-17-2018 09:00 AM
Learners_Permit
Series I Interior, Audio, and Electronics
8
09-27-2015 07:38 PM
Digitz0070
Series I Aftermarket Performance Modifications
5
09-25-2015 10:58 PM