midpipe flanges
#1
midpipe flanges
does anyone know where i can get a set of midpipe flanges. i dont really see the point of paying upwards of 200 bucks for something i can make myself, just need the flanges. i've looked around at a few sites but cant find anything, thanks
#2
Registered
Join Date: Jun 2006
Location: Dublin, Ireland
Posts: 236
Likes: 0
Received 0 Likes
on
0 Posts
Try here, http://stores.channeladvisor.com/verociousmotorsports
Don't know which flange it is you are looking for but verocious do a good range of exhaust parts.
Don't know which flange it is you are looking for but verocious do a good range of exhaust parts.
#3
Registered
Join Date: Jun 2006
Location: Dublin, Ireland
Posts: 236
Likes: 0
Received 0 Likes
on
0 Posts
I should also point out that the 3 bolt flange on the RX8 is not a standard size. This means that it is unlikely that you will find any third party flange to match it. In that case you would have to have one made specially.
Anybody got any info to the contrary?
Anybody got any info to the contrary?
#4
He's as bad as Can
#6
yea i did find the sr motorsports flanges but they are way way too expensive, by the time i bought those and the material it wouldnt be much less than any other midpipe.
The reason for making my own is saving money. If anyone has a stock midpipe near or around charlotte, NC that they'd give me or sell for real cheap so that i can cut the flanges off that would be awsome
The reason for making my own is saving money. If anyone has a stock midpipe near or around charlotte, NC that they'd give me or sell for real cheap so that i can cut the flanges off that would be awsome
#8
Can I change my username?
Join Date: Aug 2005
Location: san francisco
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
#9
does anyone have one lying around they could trace out, scan and post the measurements....i also work at a metal fab shop with a burnout table i was gonna make my own. but i would have to find something else to drive to work if i had to take exhaust apart so i could make a copy
#12
Registered
Join Date: Jun 2006
Location: Dublin, Ireland
Posts: 236
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by alec
does anyone have one lying around they could trace out, scan and post the measurements....i also work at a metal fab shop with a burnout table i was gonna make my own. but i would have to find something else to drive to work if i had to take exhaust apart so i could make a copy
Anyway's let me know.
Last edited by O'Renesis; 12-11-2006 at 01:33 PM.
#14
Registered
Join Date: Jun 2006
Location: Dublin, Ireland
Posts: 236
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by alec
that would be greatly appreciated and alot of help for sure.....yes we have auto cad but use vicon to cut everything out, which vicon opens a dxf so that would be perfect.
#15
Winning is Everything
Join Date: Aug 2006
Location: Justin, TX DFW area
Posts: 120
Likes: 0
Received 0 Likes
on
0 Posts
what is the size of the stock exhaust? Looking at making myself just a turn down after the rear axle for autox events.
I like the flanges here but
http://www.roadraceengineering.com/f...andgaskets.htm
but not sure what size to get?
I like the flanges here but
http://www.roadraceengineering.com/f...andgaskets.htm
but not sure what size to get?
#16
Registered
Join Date: Jun 2006
Location: Dublin, Ireland
Posts: 236
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by WRXtoRX8
what is the size of the stock exhaust? Looking at making myself just a turn down after the rear axle for autox events.
I like the flanges here but
http://www.roadraceengineering.com/f...andgaskets.htm
but not sure what size to get?
I like the flanges here but
http://www.roadraceengineering.com/f...andgaskets.htm
but not sure what size to get?
Last edited by O'Renesis; 12-12-2006 at 06:04 AM.
Thread
Thread Starter
Forum
Replies
Last Post
JimmyBlack
Series I Major Horsepower Upgrades
273
02-10-2020 10:23 PM
qtipconnoisseur
RX-8 Parts For Sale/Wanted
9
10-29-2015 07:19 PM
br0wm
Canada For Sale/Wanted
5
10-24-2015 11:06 PM
yapakanichi
Series I Aftermarket Performance Modifications
4
09-25-2015 07:55 PM