HKS DLI II Ignition Amp install help!
09-07-2007, 01:33 PM
#1
The Chief
Thread Starter
iTrader: (7)
Join Date: Jun 2005
Location: Virginia Beach, VA
Posts: 827
Likes: 0
Received 0 Likes
on
0 Posts
HKS DLI II Ignition Amp install help!
Can someone who has installed this with the rx8 specific harness tell me which set of wires goes to which coil. Or, if someone in Virginia Beach can read Japanese and wants to stop by for a few minutes, I'd appreciate it.
09-07-2007, 02:48 PM
#2
Guest
Posts: n/a
There should be a set of wires with a black zip tie and a set with a white one.
The black zip tie should be for the trailing coils and the white is for the leading coils. If not...
-There should be connector with (2) brown wires and (1) red, this one connects to the front leading coil,
-Then there is a connector with (2) orange wires and (1) red, this one connets to the front trailing coil,
-The third one has (2) whites and (1) red, connect this one to the rear leading,
-The last one has (2) yellows and (1) red and connects to the rear trailing coil.
The black zip tie should be for the trailing coils and the white is for the leading coils. If not...
-There should be connector with (2) brown wires and (1) red, this one connects to the front leading coil,
-Then there is a connector with (2) orange wires and (1) red, this one connets to the front trailing coil,
-The third one has (2) whites and (1) red, connect this one to the rear leading,
-The last one has (2) yellows and (1) red and connects to the rear trailing coil.
09-23-2007, 10:19 PM
#11
NO PSTNZ
Join Date: Dec 2003
Location: Gardena, CA
Posts: 287
Likes: 0
Received 0 Likes
on
0 Posts
09-24-2007, 12:09 AM
#13
NO PSTNZ
Join Date: Dec 2003
Location: Gardena, CA
Posts: 287
Likes: 0
Received 0 Likes
on
0 Posts
I hope this helps!
08-11-2008, 07:42 PM
#14
Rotary Power Rules
Join Date: Nov 2007
Location: SF Bay Area, CA
Posts: 87
Likes: 0
Received 0 Likes
on
0 Posts
08-20-2008, 11:41 PM
#15
NO PSTNZ
Join Date: Dec 2003
Location: Gardena, CA
Posts: 287
Likes: 0
Received 0 Likes
on
0 Posts
08-25-2008, 10:07 AM
#19
NO PSTNZ
Join Date: Dec 2003
Location: Gardena, CA
Posts: 287
Likes: 0
Received 0 Likes
on
0 Posts
I hope this helps!
08-27-2008, 02:23 AM
#20
Registered User
Join Date: Apr 2004
Posts: 90
Likes: 0
Received 0 Likes
on
0 Posts
thanks for your fast respond! i already try that b4, on mine, if i wiggle the unit, then the led kicks on, then after some time it will go off. my car is turbo and it puts out alot of heat, do u think heat may damage my wire harness?
thanks again for your help!!!
thanks again for your help!!!
08-27-2008, 07:01 PM
#21
The heat should not damage your wire harness, as long as it is not resting on a pipe. Many FD owners have them installed with no problem, and their under hood temps are a lot higher. That is one of the features that many people like with the HKS unit is that the box and harness itself seems to hold up to the hot engine bay of rotary cars.
08-27-2008, 09:51 PM
#22
twin powers are a mixed bag. Ever heard of the "black goo" failure? It's important to protect it from vibration and heat, they do fail.
on the rx-7 ignition system they are good for 550+rwhp though, i made 386 with one myself
on the rx-7 ignition system they are good for 550+rwhp though, i made 386 with one myself
11-23-2020, 09:34 AM
#23
New Member
Join Date: Nov 2020
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
HKS Twin Power dli II
im guessing that the wires are wired to the negative side of each coils.
Thread
Thread Starter
Forum
Replies
Last Post
kenkamm
Series I Major Horsepower Upgrades
23
07-30-2007 08:34 AM
