Lap Times
#201
I do know that feeling, rising temps normally cost me a second, or even two. I don't always use my fastest lap as a reference for next time.
The following 3 users liked this post by RE-Vision:
The following users liked this post:
hufflepuff (11-21-2019)
#204
Registered
This is primarily a SCCA STX car but I'm just having fun at the track while the weather is cold waiting for the Pro Solo season to kick off again
2004 Base Sport
2,790 lbs with 1/4 tank
Some motor I found out of some drift kid's car, leaks oil, decent compression
Sakebomb IGN-1A Coils
Off the shelf Versatuner tune
Stock Intake with K&N panel, some heat shielding.
Modified Alibaba header
TurboXS catted midpipe. (Catless for track)
3" From collector to exit, Racing Beat exhaust. All V-band.
Ron Davis Radiator
BHR Motor Mounts
SuperPro diff bushings
Kaaz 1.5 diff
255 Yokohama A052 on 17x10 Konig Hypergrams
Penske 7500da by Ankeny Racing Enterprises
560f
450r
Diftech front upper mounts, Diftech 350z bearings on stock rear mounts.
MazdaMotorsports Bar, .250 wall
Racing Beat NC Rear bar.
Mazda Motorsports offset delrin front upper control arm bushings
Diftech offset knuckle bushings
Rear bushings SuperPro
Front lower is stock.
-4 f, 0 toe
-3.5 r, 3/16 toe in
2004 Base Sport
2,790 lbs with 1/4 tank
Some motor I found out of some drift kid's car, leaks oil, decent compression
Sakebomb IGN-1A Coils
Off the shelf Versatuner tune
Stock Intake with K&N panel, some heat shielding.
Modified Alibaba header
TurboXS catted midpipe. (Catless for track)
3" From collector to exit, Racing Beat exhaust. All V-band.
Ron Davis Radiator
BHR Motor Mounts
SuperPro diff bushings
Kaaz 1.5 diff
255 Yokohama A052 on 17x10 Konig Hypergrams
Penske 7500da by Ankeny Racing Enterprises
560f
450r
Diftech front upper mounts, Diftech 350z bearings on stock rear mounts.
MazdaMotorsports Bar, .250 wall
Racing Beat NC Rear bar.
Mazda Motorsports offset delrin front upper control arm bushings
Diftech offset knuckle bushings
Rear bushings SuperPro
Front lower is stock.
-4 f, 0 toe
-3.5 r, 3/16 toe in
The following users liked this post:
hufflepuff (11-21-2019)
#209
Looks like I never shared my SoW CCW time from last year. That was my first (and so far only) time there and had a blast.
Streets of Willow CCW - 1:27.64 -- blu3dragon -- RX-8 S1, estimated at 185rwhp and 3000lbs w/driver. S2 transmission & Diff. Race seat, harness & roll bar. APR wing & DIY splitter, Fatcat coilovers, Toyo RA1 255/40/17 tires (previously used as wets).
Now that I've seen RE-Vision's lap,I need more practice, more camber, and maybe CW is faster? :-D
Streets of Willow CCW - 1:27.64 -- blu3dragon -- RX-8 S1, estimated at 185rwhp and 3000lbs w/driver. S2 transmission & Diff. Race seat, harness & roll bar. APR wing & DIY splitter, Fatcat coilovers, Toyo RA1 255/40/17 tires (previously used as wets).
Now that I've seen RE-Vision's lap,I need more practice, more camber, and maybe CW is faster? :-D
#210
Registered
#211
Registered
Looks like I never shared my SoW CCW time from last year. That was my first (and so far only) time there and had a blast.
Streets of Willow CCW - 1:27.64 -- blu3dragon -- RX-8 S1, estimated at 185rwhp and 3000lbs w/driver. S2 transmission & Diff. Race seat, harness & roll bar. APR wing & DIY splitter, Fatcat coilovers, Toyo RA1 255/40/17 tires (previously used as wets).
https://youtu.be/6iR9GMXEBjM
Now that I've seen RE-Vision's lap,I need more practice, more camber, and maybe CW is faster? :-D
Streets of Willow CCW - 1:27.64 -- blu3dragon -- RX-8 S1, estimated at 185rwhp and 3000lbs w/driver. S2 transmission & Diff. Race seat, harness & roll bar. APR wing & DIY splitter, Fatcat coilovers, Toyo RA1 255/40/17 tires (previously used as wets).
https://youtu.be/6iR9GMXEBjM
Now that I've seen RE-Vision's lap,I need more practice, more camber, and maybe CW is faster? :-D
#214
Car is built for SCCA Time Trials
~2700lb
stock motor, lot of custom bits otherwise.
Pulls a lot of G in high speed corners
315 square Yokohama A052
NCM 2:20.2
SCCA Max3 class track record, won at nationals 2019
The car in the same configuration also ran at
Putnam Park 1:16.4
Next year will likely drop a few more lbs and run Hoosiers for unlimited 2.
~2700lb
stock motor, lot of custom bits otherwise.
Pulls a lot of G in high speed corners
315 square Yokohama A052
NCM 2:20.2
SCCA Max3 class track record, won at nationals 2019
The car in the same configuration also ran at
Putnam Park 1:16.4
Next year will likely drop a few more lbs and run Hoosiers for unlimited 2.
Last edited by dallasreed; 11-21-2019 at 11:34 AM.
#216
Registered
Hit Buttonwillow CW13 this weekend. First time at this track in 4 or 5 years and the last time was just one lap in my Elantra, safe to say it's basically new to me. Got a 2:02.3, lots of little and one very big mistake to fix next time, pretty sure 2 flat or faster is achievable.
The following users liked this post:
blu3dragon (12-03-2019)
#218
Registered
was in town for 10 days. took RX-8 i bought 2 years ago to drive at street of willow
I think i did ok 1:29.8 desptite using 6 years old Champrio GT that come with car
I think i did ok 1:29.8 desptite using 6 years old Champrio GT that come with car
The following users liked this post:
RE-Vision (02-11-2020)
The following 2 users liked this post by dallasreed:
NorCalEight (05-16-2020),
wankelbolt (05-16-2020)
#224
Registered
Here is a 1:38.1 at Gingerman
Stock engine. 315 A7s. Lot of downforce and weight reduction.
https://youtu.be/5eO-GhkbZoY
Stock engine. 315 A7s. Lot of downforce and weight reduction.
https://youtu.be/5eO-GhkbZoY