RX8 Restoration (long)
#51
Glutton for punishment
Thread Starter
iTrader: (1)
Join Date: Nov 2012
Location: Brentwood
Posts: 193
Likes: 0
Received 0 Likes
on
0 Posts
JDM Mazda RX8 4 Port Automatic Motor 5 Speed Transmission RX 8 1 3 | eBay
So no unique position here. Just boredom and a high cash to intelligence ratio.
#53
Glutton for punishment
Thread Starter
iTrader: (1)
Join Date: Nov 2012
Location: Brentwood
Posts: 193
Likes: 0
Received 0 Likes
on
0 Posts
This is what happens when you intake 1l of gin and 0l of common sense. Otherwise known as a "drunken ebay binge." Then one day, an engine and transmission magically appear on your doorstep and you have to attempt to figure out why this is the case.
With all of the work I've "input" to this project, I probably should have said f-all to the 4 port and gone 6 port 6 speed instead. But for whatever reason my gin-soaked mind thought 4 port 5 speed made more sense. Don't ask. See attached picture. That is all.
With all of the work I've "input" to this project, I probably should have said f-all to the 4 port and gone 6 port 6 speed instead. But for whatever reason my gin-soaked mind thought 4 port 5 speed made more sense. Don't ask. See attached picture. That is all.
#55
Project Seca
iTrader: (10)
That plugged middle section of the back of your ECU is where that "3" harness goes on the 6MT. I've never traced, nor researched, the harness leads between the engine and transmission. I guess the complexity of splicing / rerouting weighed against a full swap would be a deciding factor. I also wonder what else is missing from the US 4 port motor. I haven't considered potential differences between the flywheel and clutch either.
This is all got to be documented already in some fashion so forgive me if I'm behind "light reading" wise.
McKennaR, is the means in which you procured the JDM motor and harness accessible to the masses or a result of a unique position you're in?
This is all got to be documented already in some fashion so forgive me if I'm behind "light reading" wise.
McKennaR, is the means in which you procured the JDM motor and harness accessible to the masses or a result of a unique position you're in?
The AT comes with a lighter counterweight, so either get a MT counterweight or get the proper flywheel/clutch to accommodate.
McKennar: Listing ended, but who was the seller? PM me a link to their account please..
#59
Project Seca
iTrader: (10)
That sucks. I'd call and compain to them about that and see if they can cover mount & balance for you since "you didnt have transportation when you initially expected" xD
In all seriousness, this waiting is really pissing me off.. I wanna know if I can keep my motor for the swap already! Im trying to compile a complete "parts remaining" list for myself..
In all seriousness, this waiting is really pissing me off.. I wanna know if I can keep my motor for the swap already! Im trying to compile a complete "parts remaining" list for myself..
#60
Glutton for punishment
Thread Starter
iTrader: (1)
Join Date: Nov 2012
Location: Brentwood
Posts: 193
Likes: 0
Received 0 Likes
on
0 Posts
The warehouse shipped them the day I paid for them so it isn't really their fault. Perhaps if I wasn't such a cheap ***, I would have sprung for UPS vs. USPS.
USPS is probably the most useless shipper of medium / large parcels in the country. I bought a set of A-pillar trim pieces from Yale02 last month, and they spent 11 days in transit from Sierra Vista, AZ. For comparison's sake: I ordered my gauge cluster and shift **** on the same day from the United Kingdom and they beat the trim panels to my house by 4 days.
In this case, I ordered another 5 M/T **** and a rear fog + switch & harness from the UK on the same day I ordered these tires and I'm pretty sure that package will get here before the tires.
USPS is probably the most useless shipper of medium / large parcels in the country. I bought a set of A-pillar trim pieces from Yale02 last month, and they spent 11 days in transit from Sierra Vista, AZ. For comparison's sake: I ordered my gauge cluster and shift **** on the same day from the United Kingdom and they beat the trim panels to my house by 4 days.
In this case, I ordered another 5 M/T **** and a rear fog + switch & harness from the UK on the same day I ordered these tires and I'm pretty sure that package will get here before the tires.
#62
Glutton for punishment
Thread Starter
iTrader: (1)
Join Date: Nov 2012
Location: Brentwood
Posts: 193
Likes: 0
Received 0 Likes
on
0 Posts
Anyone know which PID in the generic OBDII monitor will tell me AFR's?
1st gear WOT from a 5mph roll: (old coils, getting a misfire hence flashing CEL)
I'll take some requests for videos if anyone has them. Keep in mind the car isn't registered (is insured) so I can't drive it on a public road. I live on a golf course (private road), and thus have a tiny bit of deserted straightaway on one of the maintenance access roads on the backside of the course, but I only have enough road to maybe hit 3rd before I come up on a driveway.
1st gear WOT from a 5mph roll: (old coils, getting a misfire hence flashing CEL)
I'll take some requests for videos if anyone has them. Keep in mind the car isn't registered (is insured) so I can't drive it on a public road. I live on a golf course (private road), and thus have a tiny bit of deserted straightaway on one of the maintenance access roads on the backside of the course, but I only have enough road to maybe hit 3rd before I come up on a driveway.
Last edited by McKennaR; 02-05-2013 at 05:17 PM.
#63
Glutton for punishment
Thread Starter
iTrader: (1)
Join Date: Nov 2012
Location: Brentwood
Posts: 193
Likes: 0
Received 0 Likes
on
0 Posts
Took it on another test drive after replacing the coils with the new set. No more misfires, U0101 remains however.
Ran it from first to redline in third before I ran out of road. I did not video that particular run, as I needed both hands and 100% concentration. It's a narrow road with a bit of an off-camber bend in the middle.
Nothing of note to report, other than that I'm rubbish at this clutch (as the video below clearly shows).
No hiccups, no jerky-acceleration, no in-gear rev limits or anything like that. It's not a particularly fast car, but it gets out of it's own way.
True test will be logging AFR's whenever my AP gets here, and who knows when that will be.
Until then, even with the CEL I'd feel comfortable daily driving this car. Which is nice, because that's the intent once it gets out to CA.
Keep those PM's / replies coming if you have any questions about this transplant.
I'll leave you with a pic of the car as it sits today and a video of a 5 - 60mph roll. As I mentioned above, I'm not 100% used to this particular gearbox / clutch yet, hence the awful 1 - 2 shift.
Cheers,
Ryan
Ran it from first to redline in third before I ran out of road. I did not video that particular run, as I needed both hands and 100% concentration. It's a narrow road with a bit of an off-camber bend in the middle.
Nothing of note to report, other than that I'm rubbish at this clutch (as the video below clearly shows).
No hiccups, no jerky-acceleration, no in-gear rev limits or anything like that. It's not a particularly fast car, but it gets out of it's own way.
True test will be logging AFR's whenever my AP gets here, and who knows when that will be.
Until then, even with the CEL I'd feel comfortable daily driving this car. Which is nice, because that's the intent once it gets out to CA.
Keep those PM's / replies coming if you have any questions about this transplant.
I'll leave you with a pic of the car as it sits today and a video of a 5 - 60mph roll. As I mentioned above, I'm not 100% used to this particular gearbox / clutch yet, hence the awful 1 - 2 shift.
Cheers,
Ryan
Last edited by McKennaR; 02-05-2013 at 05:20 PM.
#66
weeeeeeeeee
iTrader: (12)
Here are some PIDs for you, including Wideband O2:
Code:
LTFT Long Term Fuel Trim? OBD2 PID: 0107 Long Name: LTFT Short Name: LTFT Minimum Value: -25 Maximum Value: 25 Scale Factor: x1 Unit Type: % Equation: (A-128)*100/128 Gen 1 Status: Gen 2 Status: Working and confirmed MS6 Status: STFT Short Term Fuel Trim? OBD2 PID: 0106 Long Name: STFT Short Name: STFT Minimum Value: -25 Maximum Value: 25 Scale Factor: x1 Unit Type: % Equation: (A-128)*100/128 Gen 1 Status: Gen 2 Status: Working and confirmed MS6 Status: Fuel Pressure OBD2 PID: 0123 Long Name: FP Short Name: FP Minimum Value: 0 Maximum Value: 2500 Scale Factor: x1 Unit Type: % Equation: (A*256+B)*10*.145 Gen 1 Status: Gen 2 Status: Working and confirmed MS6 Status: Open Loop Commanded Air/Fuel Ratio OBD2 PID: 0144 Long Name: AFR Short Name: AFR Minimum Value: 0 Maximum Value: 20 Scale Factor: x1 Unit Type: A/F Equation: (A*256+B)/32768*14.7 Gen 1 Status: Gen 2 Status: Working and confirmed MS6 Status: OEM Wideband Air/Fuel Ratio OBD2 PID: 0134 Long Name: WAFR Short Name: WAFR Minimum Value: 0 Maximum Value: 20 Scale Factor: x1 Unit Type: A/F Equation: (A*256+B)/32768*14.7 Gen 1 Status: Gen 2 Status: Working and confirmed MS6 Status: Cat Temp OBD2 PID: 013c Long Name: Cat Temp Short Name: Cat Temp Minimum Value: 0 Maximum Value: 2000 Scale Factor: x1 Unit Type: F Equation: ((A*256+B)/10-40)*1.8+32 Gen 1 Status: Gen 2 Status: Working and confirmed MS6 Status: Absolute Load OBD2 PID: 0143 Long Name: Abs Load Short Name: Abs Load Minimum Value: 0 Maximum Value: 255 Scale Factor: x1 Unit Type: % Equation: (A*256+B)*100/255 Gen 1 Status: Gen 2 Status: Working and confirmed MS6 Status: Intake Manifold Absolute Pressure OBD2 PID: 010b Long Name: IMAP Short Name: IMAP Minimum Value: 0 Maximum Value: 100 Scale Factor: x1 Unit Type: PSI Equation: A*.145 Gen 1 Status: Gen 2 Status: Working and confirmed MS6 Status:
#69
Glutton for punishment
Thread Starter
iTrader: (1)
Join Date: Nov 2012
Location: Brentwood
Posts: 193
Likes: 0
Received 0 Likes
on
0 Posts
Thanks.
Might be worth noting that cruise control doesn't work right now, though no DTC pertains to it. Cruise master pops up on the dash, but at no time or speed will cruise work.
After searching, I can't figure out whether these cars are like my Subaru's wherein when the CEL is illuminated, cruise is automatically disabled.
Thoughts?
Might be worth noting that cruise control doesn't work right now, though no DTC pertains to it. Cruise master pops up on the dash, but at no time or speed will cruise work.
After searching, I can't figure out whether these cars are like my Subaru's wherein when the CEL is illuminated, cruise is automatically disabled.
Thoughts?
#71
Glutton for punishment
Thread Starter
iTrader: (1)
Join Date: Nov 2012
Location: Brentwood
Posts: 193
Likes: 0
Received 0 Likes
on
0 Posts
The only PIDs from that list the AuTel will log and graph in real time are:
LTFT
STFT
STFTB1S4 (or one of those BxSx PIDs)
Absolute Load(%)
Cat Temp
No AFR / WAFR or fuel pressure.
Torque is currently INOP now too because I... uh... may or may not have broken the ELM 327 the other day in my haste to exit my Subaru into which it was plugged.
I've hit the point in the budget where I either have to sell more parts (which nobody is buying) or choose between a new rear bumper skin and an access port... or sleeping on the couch when the wife gets our joint account statement at the end of this month and sees that I bought both.
Such is the life of a car addict.
So uh, if anyone's looking for some sweet, sweet 4 port parts goodness, pop on over to the For Sale forum and fund the purchase of my AP by buying my stuff. On an unrelated note, anyone need a kidney?
LTFT
STFT
STFTB1S4 (or one of those BxSx PIDs)
Absolute Load(%)
Cat Temp
No AFR / WAFR or fuel pressure.
Torque is currently INOP now too because I... uh... may or may not have broken the ELM 327 the other day in my haste to exit my Subaru into which it was plugged.
I've hit the point in the budget where I either have to sell more parts (which nobody is buying) or choose between a new rear bumper skin and an access port... or sleeping on the couch when the wife gets our joint account statement at the end of this month and sees that I bought both.
Such is the life of a car addict.
So uh, if anyone's looking for some sweet, sweet 4 port parts goodness, pop on over to the For Sale forum and fund the purchase of my AP by buying my stuff. On an unrelated note, anyone need a kidney?
#72
Glutton for punishment
Thread Starter
iTrader: (1)
Join Date: Nov 2012
Location: Brentwood
Posts: 193
Likes: 0
Received 0 Likes
on
0 Posts
My mail guy must think I'm a heroin addict or something... every time I get packages from the UK they show up wrapped in a black trash bag surrounded what looks like half a roll of tape.
This was my 2nd 5 M/T **** and a rear fog setup.
**** is in the car, rear fog is waiting on a good rear bumper skin so I can install it.
I think I just inadvertently converted the car to a standard power Euro market RX8 with the 4 port 5mt and rear fog. I mean, the 4 port 5mt was on purpose, but it originally wasn't my intent to replicate a standard power euro car.
Oh and until I can find the correct radio and cruise control buttons from an M/T steering wheel, electrical tape will cover the "down" a/t paddle shift buttons. I already removed the up paddles.
If I were going for a proper euro 192ps replica, I'd probably get the blank panel that covers where the cruise control buttons are on the USDM cars, as my cruise doesn't work now (yet?) and as far as I know, cruise wasn't offered as an option on the euro cars.
This was my 2nd 5 M/T **** and a rear fog setup.
**** is in the car, rear fog is waiting on a good rear bumper skin so I can install it.
I think I just inadvertently converted the car to a standard power Euro market RX8 with the 4 port 5mt and rear fog. I mean, the 4 port 5mt was on purpose, but it originally wasn't my intent to replicate a standard power euro car.
Oh and until I can find the correct radio and cruise control buttons from an M/T steering wheel, electrical tape will cover the "down" a/t paddle shift buttons. I already removed the up paddles.
If I were going for a proper euro 192ps replica, I'd probably get the blank panel that covers where the cruise control buttons are on the USDM cars, as my cruise doesn't work now (yet?) and as far as I know, cruise wasn't offered as an option on the euro cars.
#74
Glutton for punishment
Thread Starter
iTrader: (1)
Join Date: Nov 2012
Location: Brentwood
Posts: 193
Likes: 0
Received 0 Likes
on
0 Posts
Where did you end up sourcing your gearbox?