9krpmrx8

iTrader: (46)

Damn, how could I miss that?

cornholio135

iTrader: (2)

I have super secret ebay searching powers that I cannot reveal....

9krpmrx8

iTrader: (46)

I'll "buy it now" for $20.00.

hoss -05

iTrader: (4)

Good game guys! I loved the outcome... of course.

VS8

iTrader: (4)

my motor is pissing me off...
only thing standing between me and a finished motor is 1 rear stationery gear screw

9krpmrx8

iTrader: (46)

The outcome was absolute bullshit!!!!!


You need one or it was damaged?

autotragic rx8

..................lol

VS8

iTrader: (4)

i need one...i believe its a special lockscrew
gotta order it from mazda

8 Maniac

iTrader: (1)

Well, was tired of waiting so I got my second clip with the new exhaust. The parking lot I used was a little shorter than the first one I used so I had to brake immediately after redline but you can still get the general idea.

http://www.youtube.com/watch?v=LB2HUq1hRaY

[embed]LB2HUq1hRaY[/embed]

9krpmrx8

iTrader: (46)

Damn, it's louder!!! I love it.

Grungepup

iTrader: (2)

sounds good... i noticed it the day you left, i could here you getting on it turning on to callaghan

8 Maniac

iTrader: (1)

Is it really that loud? lol. I dont think I even hit redline at that time since I had the old exhaust resting in my rear seats.

Grungepup

iTrader: (2)

yup.... it was noticable

tbk

iTrader: (3)

My damn exhaust is taking too long to get here! >:[

9krpmrx8

iTrader: (46)

A watched pot never boils.

cornholio135

iTrader: (2)

Are "We" going to install this at Jay's?
I am really curius how it sounds...
for $499 with resonated midpipe that is a deal...

9krpmrx8

iTrader: (46)

Juan make sure you have all the gaskets,. etc. when you get it.

Hey corn, I need to splice a larger 18 gauge wire into the much smaller ground on the cigarette lighter. I tried to use a quick splice but it does not splice into the smaller wire to make a connection. Currently I have it grounded to a bolt but I am getting intermittent error codes on my gauge and they say its due to a bad ground.

Grungepup

iTrader: (2)

you might have to cut the wires and go with a butt splice or even a bean splice, i have never seen anything that will allow for splicing of different gauges

Grungepup

iTrader: (2)

my garage is always open..... i will helping autotragic install the satty radio in his car this saturday

9krpmrx8

iTrader: (46)

I don't want to have to cut or solder because there is no damn room to work as it is. But I guess I will have too. Can I come Saturday? I wanna install my grounding kit and fix this gauge. My tire guy was out and still has the minivan. I want my freakin' rims already.

Grungepup

iTrader: (2)

sure... come on over

if possible check out my dads car to see what is causing the "clicking"

9krpmrx8

iTrader: (46)

Yeah we can check it out. You have a soldering iron and solder?

Grungepup

iTrader: (2)

that i do not have.... i use to but dont know what happened to it.... just glad i found my dremel for now lol

cornholio135

iTrader: (2)

just split the ground wire from the lighter and use a butt connector to attach the wire for gauge wire as in this pic below

if there is no room get a T Tap and Male Blade connector

9krpmrx8

iTrader: (46)

So two wires in the end of one butt connector? The wire from the oil temp gauge is 18 gauge.