Single Rotor Lawn-Mower!!!
Thread Starter
Un-Registered User
Joined: Aug 2012
Posts: 1,209
Likes: 3
From: NZ Brahhhhh
Single Rotor Lawn-Mower!!!
Not sure if repost
Built in New Zealand
Here's some info (copied from trade-me (NZ's ebay) auction)
ENGINE: CUSTOM MAZDA 13B SINGLE ROTOR
ENGINE SPECS: SERIES 6 RX7 SIDE PLATES WITH FULL CUT BRIDGEPORT. S6 ROTOR HOUSING PORTED AS REQUIRED.FULLY LIGHTENED ROTOR WITH 3MM CARBON APEX SEALS AND SOLID CORNER SEALS. S6 STATIONARY GEARS WITH WINDOWED BEARINGS. S6 OIL PUMP WITH MODIFIED AND POLISHED OIL GALLERIES.CUSTOM 4L. SUMP. ALL NEW GASKETS BEARINGS AND SEALS THROUGHOUT. GILMOUR BELTS AND PULLEYS.RECONDITIONED ALTERNATOR AND STARTER MOTOR.
EVERYTHING IN THIS ENGINE HAS BEEN LIGHTENED RIGHT FROM THE FLYWHEEL TO THE OIL PUMP PULLEY.FULL ASSEMBLY HAS BEEN BALANCED
INTAKE: DALORTTO SIDE DRAFT WITH CUSTOM FLOWED INLET MANIFOLD.
EXHAUST: FLOWED 2" WITH HEAT WRAP TO STRAIGHT THROUGH MUFFLER WITH 2.5" EXIT. GOOD FLAMES FOR ROASTING MARSH MALLOWS.
COOLING,(WATER AND OIL):SERIES 6 RX7 OIL COOLER WITH CUSTOM OIL LINES AND FITTINGS COURTESY OF PIRTEK. NISSAN VANETTE 2 CORE RADIATOR.10" FAN AND ALSO PUSHING FAN ON FRONT.
DRIVETRAIN: TOYOTA SUPRA GEARBOX,RX3 BELL HOUSING WITH ADAPTER PLATE. 5 SPEED. 10 POUND FLYWHEEL AND SUPRA CLUTCH.CUSTOM 4'' DRIVESHAFT.
DIFF: NISSAN VANETTE. SHORTENED AND LOCKED.NEW SEALS THROUGHOUT.
ALL ENGINE WORK HAS BEEN DONE BY LUKE RUSSELL AT AVENUE AUTOPORT LTD.
ENGINE HAS BEEN DYNOTUNED AND MADE 103HP WITH 300NM OF TORQUE AT THE WHEELS.
Enjoy guys
Built in New Zealand
Here's some info (copied from trade-me (NZ's ebay) auction)
ENGINE: CUSTOM MAZDA 13B SINGLE ROTOR
ENGINE SPECS: SERIES 6 RX7 SIDE PLATES WITH FULL CUT BRIDGEPORT. S6 ROTOR HOUSING PORTED AS REQUIRED.FULLY LIGHTENED ROTOR WITH 3MM CARBON APEX SEALS AND SOLID CORNER SEALS. S6 STATIONARY GEARS WITH WINDOWED BEARINGS. S6 OIL PUMP WITH MODIFIED AND POLISHED OIL GALLERIES.CUSTOM 4L. SUMP. ALL NEW GASKETS BEARINGS AND SEALS THROUGHOUT. GILMOUR BELTS AND PULLEYS.RECONDITIONED ALTERNATOR AND STARTER MOTOR.
EVERYTHING IN THIS ENGINE HAS BEEN LIGHTENED RIGHT FROM THE FLYWHEEL TO THE OIL PUMP PULLEY.FULL ASSEMBLY HAS BEEN BALANCED
INTAKE: DALORTTO SIDE DRAFT WITH CUSTOM FLOWED INLET MANIFOLD.
EXHAUST: FLOWED 2" WITH HEAT WRAP TO STRAIGHT THROUGH MUFFLER WITH 2.5" EXIT. GOOD FLAMES FOR ROASTING MARSH MALLOWS.
COOLING,(WATER AND OIL):SERIES 6 RX7 OIL COOLER WITH CUSTOM OIL LINES AND FITTINGS COURTESY OF PIRTEK. NISSAN VANETTE 2 CORE RADIATOR.10" FAN AND ALSO PUSHING FAN ON FRONT.
DRIVETRAIN: TOYOTA SUPRA GEARBOX,RX3 BELL HOUSING WITH ADAPTER PLATE. 5 SPEED. 10 POUND FLYWHEEL AND SUPRA CLUTCH.CUSTOM 4'' DRIVESHAFT.
DIFF: NISSAN VANETTE. SHORTENED AND LOCKED.NEW SEALS THROUGHOUT.
ALL ENGINE WORK HAS BEEN DONE BY LUKE RUSSELL AT AVENUE AUTOPORT LTD.
ENGINE HAS BEEN DYNOTUNED AND MADE 103HP WITH 300NM OF TORQUE AT THE WHEELS.
Enjoy guys
New Member
Joined: Jun 2018
Posts: 2
Likes: 0
300nm of torque from 103hp dosent that seem strange to some. 300nm is around 221 ft lb that more then a 13b so how the heck did they get some much out of a single rotor here is another strange one https://touch.trademe.co.nz/motors/listing/view/369433004 and they got 400nm from 165HP. 400nm is 295 footFoot-pound of torque.
Last edited by Speedy rotor; Jun 27, 2018 at 10:54 AM.
300nm of torque from 103hp dosent that seem strange to some. 300nm is around 221 ft lb that more then a 13b so how the heck did they get some much out of a single rotor here is another strange one https://touch.trademe.co.nz/motors/l...view/369433004 and they got 400nm from 165HP. 400nm is 295 footFoot-pound of torque.
New Member
Joined: Jun 2018
Posts: 2
Likes: 0
well i dont know why the age of the thread would matter, there been older one, but asfar as the video link not work who know people take video down all the time. I was just curious to find a dyno graph for one of these single rotary engine other then the one at atkinsrotary
Thread
Thread Starter
Forum
Replies
Last Post
shinboy
Series I Aftermarket Performance Modifications
1
May 21, 2006 05:54 AM
