APU Rx-8 Rebuild Service
12-12-2013, 03:58 PM
#1
Former Sponsor
Thread Starter
Join Date: Nov 2013
Posts: 108
Likes: 0
Received 0 Likes
on
0 Posts
APU Rx-8 Rebuild Service
We feel this service is key now that warranties are running out.
It truly would be a shame to see even more abandoned and non running vehicles.
We are very active in the Rx vehicle community and rx7club and have been for years. We hope to be just as helpful and active with the Rx-8 community.
What we are offering
Here is what is included.
13B-MSP (renesis) freshly rebuilt with 12 month warranty
Freshly resurfaced great condition housings and Irons in excellent Shape
Factory Matched weight rotors
New Rotor Bearings
New Apex Seals (of buyers choice price varies)
New Apex Seal Springs
New Corner seal springs
New Corner Seal rubber inserts
New Side Seal Springs
New Oil Control Ring Springs
New Viton Oil Control Rings
New Side Seals
New Corner Seals
All new internal O-Ring Set(Coolant Seals,Dowel Pins, etc
Good condition Factory Oil Pump
New Atkins Thermal Pellet
New Front and Rear Main Seals
New Pilot Bearing
The engine is not built yet so the purchaser has the choice of what type of porting they would like and paint of the block
Cost for the short block is $3500.00 plus shipping (this is dependent on seal choice and if there are any damages to internals).
Warranty is 12 months, unlimited mileage. Warranty covers labor of engine build if any issue is to arise. Warranty does not and will not cover any shipping fees or shop/labor fees if install/uninstall is performed by a shop. We feel like we are very fair in the rare event something is to go wrong. Upon tear down of an engine it is usually very obvious if an issue was builder error or detonation/abuse by engine owner.
You can choose to add the following for additional costs thought the parts I will be using will be in great shape and no need to replace:
New Oil Control Rings-$260.00
New Front and Rear Stationary Bearings-$125.00
Other parts you can add-
Longblock parts (LIM,UIM, TB, Waterhousing, Waterpump, Bracket for PS and Ac, Alternator, good used ignition coils, Fuel system, Oil filler neck, front pullies) Powdercoated the color you want (Except for Tb) for $650 or $400 un coated
Any Brand new Act, Exedy, or Spec Clutch.
We can also offer a full custom build for anyone that wants to go forced induction, 3rotor swap, REW swap ect ect.
Buyer is to send a $500.00 non-refundable deposit for the engine when they decide they want to purchase it, and turn around time will be around 2-3 weeks.
Each motor will be well documented with Pictures that they will receive with the block.
Please let me know if you have any questions.
It truly would be a shame to see even more abandoned and non running vehicles.
We are very active in the Rx vehicle community and rx7club and have been for years. We hope to be just as helpful and active with the Rx-8 community.
What we are offering
Here is what is included.
13B-MSP (renesis) freshly rebuilt with 12 month warranty
Freshly resurfaced great condition housings and Irons in excellent Shape
Factory Matched weight rotors
New Rotor Bearings
New Apex Seals (of buyers choice price varies)
New Apex Seal Springs
New Corner seal springs
New Corner Seal rubber inserts
New Side Seal Springs
New Oil Control Ring Springs
New Viton Oil Control Rings
New Side Seals
New Corner Seals
All new internal O-Ring Set(Coolant Seals,Dowel Pins, etc
Good condition Factory Oil Pump
New Atkins Thermal Pellet
New Front and Rear Main Seals
New Pilot Bearing
The engine is not built yet so the purchaser has the choice of what type of porting they would like and paint of the block
Cost for the short block is $3500.00 plus shipping (this is dependent on seal choice and if there are any damages to internals).
Warranty is 12 months, unlimited mileage. Warranty covers labor of engine build if any issue is to arise. Warranty does not and will not cover any shipping fees or shop/labor fees if install/uninstall is performed by a shop. We feel like we are very fair in the rare event something is to go wrong. Upon tear down of an engine it is usually very obvious if an issue was builder error or detonation/abuse by engine owner.
You can choose to add the following for additional costs thought the parts I will be using will be in great shape and no need to replace:
New Oil Control Rings-$260.00
New Front and Rear Stationary Bearings-$125.00
Other parts you can add-
Longblock parts (LIM,UIM, TB, Waterhousing, Waterpump, Bracket for PS and Ac, Alternator, good used ignition coils, Fuel system, Oil filler neck, front pullies) Powdercoated the color you want (Except for Tb) for $650 or $400 un coated
Any Brand new Act, Exedy, or Spec Clutch.
We can also offer a full custom build for anyone that wants to go forced induction, 3rotor swap, REW swap ect ect.
Buyer is to send a $500.00 non-refundable deposit for the engine when they decide they want to purchase it, and turn around time will be around 2-3 weeks.
Each motor will be well documented with Pictures that they will receive with the block.
Please let me know if you have any questions.
12-17-2013, 10:38 AM
#3
location?
sent from my droid DNA while gettin jiggy with your mom...big ***** style
sent from my droid DNA while gettin jiggy with your mom...big ***** style
12-17-2013, 01:27 PM
#5
thanks
are you the guys that work closely with rotary resurrection?
sent from my droid DNA while gettin jiggy with your mom...big ***** style
are you the guys that work closely with rotary resurrection?
sent from my droid DNA while gettin jiggy with your mom...big ***** style
Thread
Thread Starter
Forum
Replies
Last Post
gwailo
New Member Forum
30
06-07-2020 12:21 PM