I can answer my own question. They are not the same...connectors are different. Can maybe repin and it'll work? I don't know.
|
Yes, the Sensors in S1 and S2's are definitely different, and naturally OEM Part Numbers.
From what I can concur with the main differences are in the wiring aspect/design, the S2 has a later designed Wiring Connect PLUGs which is not interchangeable with their main Wiring Loom connects between Series of RX-8. Remember there are also differences between Auto Transmissions and between the 5 speed and the 6 speed Manual Transmissions too. In the USA for the S1 RX-8 the Exhaust Manifolds (sorry Header) Air Fuel Ratio Sensor appears to be still sold as a genuine OEM unit. Whereas the S1 OEM O2 Sensor used in the CAT is a recon unit (9U). For S2 (Manual Trans) all the parts are different by Part Number and are all OEM no recons and are still all genuine. (and more expensive too) Just to add to the confusion the 02 CAT Sensor in S2 Automatic uses the exact same S1 Sensor N3H2-18-861C-9U recon. Repining, ?? Well I honestly can not say, as I cant recall reading about anyone's experience in forums. |
Can S1 front sway bar end links fit an S2 and vice versa? For a 2007 model the part number is F15134150 and for a 2010 it's F18934150. So the part numbers are definitely different. But will they fit?
|
Yes, although they do not technically supersede the F189 is the better link, F151 were known to break at ball joint housing (they can all break, but the F189 is/was said to be better made).
|
Originally Posted by ASH8
(Post 4726640)
Yes, although they do not technically supersede the F189 is the better link, F151 were known to break at ball joint housing (they can all break, but the F189 is/was said to be better made).
|
As you can see here, the part numbers for sway bars and bushings differ between sport and normal versions, but there is only 1 part number for each end link.
|
Originally Posted by Steve Dallas
As you can see here, the part numbers for sway bars and bushings differ between sport and normal versions, but there is only 1 part number for each end link.
By the way, that's the exact website I'm going to order these parts from :) |
Quick question, are the S2 oil cooler air inlet ducts made out of flexible rubber like the S1 oil cooler ducts?
|
Anyone know where I can buy the "LENS" that goes over the Speedometer Gauge? Just the Lens / Clear plastic piece, mine has a scratch in it from the previous owner and it's pretty big.
2006 / Shinka Ed. |
Ash, can you tell me PNs for the driver's side (US Left) A-pillar cover (cream colored plastic only - previous owner smoked) as well as the clips in the trunk liner hardware, both the push-style center and threaded?
2009 R3 |
F152-68-170D77 Pillar Trim Left
B040-68-865A00 Clip (15 used) GJ21-68-885B02 Clip (9 used) |
Thanks man. You're a machine!
|
Sunroof
I have a 2007 Rx8 GT model. Does anyone know the part number for this plastic device that goes up (when opening sunroof) and down (when closing). It's located in the front of the sunroof opening.
|
IF you are talking about the Deflector , see Diagram # 8
F153-69-880A Defelector, about $73 https://www.parkmazdaoemparts.com/pa...&siteid=215334 |
Thanks.
Originally Posted by ASH8
(Post 4759965)
IF you are talking about the Deflector , see Diagram # 8
F153-69-880A Defelector, about $73 https://www.parkmazdaoemparts.com/pa...&siteid=215334 |
ok no problem
|
I've got a dumb one for you, Ash. I've got no mounting strap in the trunk for the inflator kit and can't find any reference to that hardware in the online catalogs. Can you tell me anything about the strap, trunk fasteners and the clips at each end?
|
Already listed trunk trim clips, see above.
Strap for repair kit.. https://www.parkmazdaoemparts.com/pa...&siteid=215334 |
Sorry man. Thanks.
|
OK. How about this one for a challenge. I've looked everywhere and can't find the part number for those clip/washer/spacer things that fit between the rear caliper and its bracket. Here's a pic of it.
https://cimg1.ibsrv.net/gimg/www.rx8...915befc061.jpg |
|
^ Thank you!
|
Ash, hoping you might help me find something.
I'm looking for the 3 lines that come off the intake hose. (what's attached to #11) I don't need the plastic connectors since they're going on an AEM intake https://cimg8.ibsrv.net/gimg/www.rx8...3aa951747c.gif |
Hey man, got a full VIN, I know you gave it to be before but I don't record them.
Need it in a hurry as going out in 30 minutes.. :) Edit, your is about a 2007 6 port manual, yes? VIN will tell me. |
Steve fwiw I removed those clips as mine only had 3.
No I'll effects so far. Travis |
All times are GMT -5. The time now is 02:27 PM. |
© 2024 MH Sub I, LLC dba Internet Brands