Tein S tech full drop time
12-24-2007, 01:02 AM
#3
I made some poos
iTrader: (1)
Join Date: Sep 2005
Location: Pittsburgh, PA
Posts: 841
Likes: 0
Received 0 Likes
on
0 Posts
The front drops almost immediately and the rear will take about a 100 miles or so. Also, don't get an alignment for a couple hundred miles so that when you do they are properly settled and won't mess up the alignment further down the road. And Post some PICS!!!
12-24-2007, 10:45 AM
#4
Registered
Thread Starter
hmmmmm ill post some pics when i have chance, i have been working in the day so much so havent had chance too. If you say the front drops more, i guess i was expecting more. Ill post some pics and you guys can tell me what you think.
pre load the springs? i dont know to be honest my fried dinstalled them?
pre load the springs? i dont know to be honest my fried dinstalled them?
12-24-2007, 10:50 AM
#5
Registered User
Join Date: Nov 2006
Posts: 987
Likes: 0
Received 0 Likes
on
0 Posts
hmmmmm ill post some pics when i have chance, i have been working in the day so much so havent had chance too. If you say the front drops more, i guess i was expecting more. Ill post some pics and you guys can tell me what you think.
pre load the springs? i dont know to be honest my fried dinstalled them?
pre load the springs? i dont know to be honest my fried dinstalled them?
12-24-2007, 10:56 AM
#6
Administrator
iTrader: (7)
taken from another thread:
Never fear, Jedi is here!
Your ride height didn't lower because the shop most likely did not pre-load the springs. Turn your wheel completely to one direction. Get in there and loosen the two upper control arm bolts. (very easy to do, no need to go back to the shop) I think it's a 17 mm???
Loosen then 80% of the way, let sit for 30 minutes, retighten and BINGO, your car will lower slightly and the springs will settle within a few days / week depending on how much you drive.
Your ride height didn't lower because the shop most likely did not pre-load the springs. Turn your wheel completely to one direction. Get in there and loosen the two upper control arm bolts. (very easy to do, no need to go back to the shop) I think it's a 17 mm???
Loosen then 80% of the way, let sit for 30 minutes, retighten and BINGO, your car will lower slightly and the springs will settle within a few days / week depending on how much you drive.
12-24-2007, 12:28 PM
#8
Banned
Join Date: Oct 2007
Posts: 35
Likes: 0
Received 0 Likes
on
0 Posts
12-24-2007, 12:53 PM
#9
Administrator
iTrader: (7)
trust in the Jedi you must.
I installed 2 sets of Konis + S Techs a few months ago and preloading was necessary.
I installed 2 sets of Konis + S Techs a few months ago and preloading was necessary.
12-24-2007, 01:33 PM
#14
Banned
Join Date: Oct 2007
Posts: 35
Likes: 0
Received 0 Likes
on
0 Posts
[QUOTE=Mikeluvs8;2207599]I Didnt Pre Load My Springs And My Car Is Probably Lower Than All Your Cars!!
Join Date: Jan 2006
Location: from the SF BAY to LAS VEGAS
Posts: 1,250
Likes: 0
Received 0 Likes
on
0 Posts
12-24-2007, 01:46 PM
#18
I don't buy Kool-Aid
You dont need to pre load, just let them settle. Mike did my the work on my 8 and I can tell you first hand, If was a dam good job and my drop looks sick! N.S.
12-24-2007, 01:48 PM
#20
Banned
Join Date: Jan 2006
Location: from the SF BAY to LAS VEGAS
Posts: 1,250
Likes: 0
Received 0 Likes
on
0 Posts
12-24-2007, 02:19 PM
#21
Less Weight = Better RX8
Do you guys recommend chaning the shocks when you do this? If so, then what shock. My car has 48k and I think it is time to replace the shocks. Might as well lower it as well.
Let me know what you think.
Let me know what you think.
12-24-2007, 02:19 PM
#22
I made some poos
iTrader: (1)
Join Date: Sep 2005
Location: Pittsburgh, PA
Posts: 841
Likes: 0
Received 0 Likes
on
0 Posts
You don't have to loosen the control arm bolts, but the front will drop immediately if you do so it is highly suggested. If you do it then there will be no need to let it settle as it is already dropped the full amount. If you don't do it, the front will eventually settle to the correct height, but why wait if you can have it at the full drop right after the install. The rear will take a little time to settle but it won't be much maybe an 1/8 inch or so.
12-24-2007, 03:16 PM
#23
I don't buy Kool-Aid
You don't have to loosen the control arm bolts, but the front will drop immediately if you do so it is highly suggested. If you do it then there will be no need to let it settle as it is already dropped the full amount. If you don't do it, the front will eventually settle to the correct height, but why wait if you can have it at the full drop right after the install. The rear will take a little time to settle but it won't be much maybe an 1/8 inch or so.
-Gil
12-24-2007, 03:43 PM
#24
I made some poos
iTrader: (1)
Join Date: Sep 2005
Location: Pittsburgh, PA
Posts: 841
Likes: 0
Received 0 Likes
on
0 Posts
yeah, i'm not saying that it isn't going to drop, just that it will still have to settle which you even say in your post took about 4-5 days. I'm impatient, and I like instant results so I tightened the bolts on the ground and it was dropped from day 1, no need to wait for it to settle (in the front at least).
12-24-2007, 03:48 PM
#25
I made some poos
iTrader: (1)
Join Date: Sep 2005
Location: Pittsburgh, PA
Posts: 841
Likes: 0
Received 0 Likes
on
0 Posts
Also, the drop you noticed at first was because the springs are shorter than stock. The drop you have now is because the control arms are now used to their new position and have shifted. The shift is basically what the "pre-loading" does. It tightens them in the new position, instead of waiting for them to shift into the new position while tightened. Anyways, I'm off to get drunk, Happy Holidays!!