9krpmrx8

iTrader: (46)

Thanks for the link, good thread. I might have to contact them about the Swift springs, maybe that is the ticket.

Highway8

iTrader: (11)

Swift springs are very nice and BTW swift color codes their springs 65mm ID are gold, 60mm are silver, 70mm are blue. Also do yourself a favor and add some helper or assist springs http://www.swiftsprings.net/products...t_springs.html . It will be more comfortable on the street, won't hurt performance one bit (can actually help), you can run a shorter 6 or 7 inch spring instead of that 8 or 9 inch which saves unsprung weight. Chances are you only have 5-6" of shock travel anyways. The Assist or helper spring will add 1" of useable stroke and removing 2" of spring only reduces your useable stroke by less then 1", so a 6" spring with a helper/assist spring will actual add spring stroke to your setup.

Throw some thrust sheets in there too http://www.swiftsprings.net/products..._products.html.

Swift springs are not cheap though. Retail for $100 each. For 25% off retail and great service, call track worx at 714-872-2514.

comebackqid

iTrader: (13)

Same thing with mine bro! I figure by the end of this year I will be switching to JIC's

imput1234

iTrader: (6)

From what your describing, you might want to get it properly valved. That will help more.

9krpmrx8

iTrader: (46)

So I pulled the rears to raise up the rear and discovered that the lower bushings in both rears are cracked. Pretty sad considering they have under 1,000 miles on them. I'm going to send Stance some pics and see what they say.

J8635621

iTrader: (10)

lol GOOD LUCK WITH THAT ONE

brilliantblackrx8

I am curious if you can run the Swift 250# spring with a Koni yellow?

9krpmrx8

iTrader: (46)

http://www.flickr.com/photos/9krpmrx8/7207450750/http://www.flickr.com/photos/9krpmrx8/7207450090/http://www.flickr.com/photos/9krpmrx8/7207449446/http://www.flickr.com/photos/9krpmrx8/7207448958/

hoss -05

iTrader: (4)

Do you think cheap megan racing coil-overs have all these problems?

paimon.soror

iTrader: (15)

Yup, mine was similar, not as bad, but I attribute that to your warmer climate mixed with the dry rubber they use. My experience with stance was that they sent me brand new lower shock mounts (i.e. the screw on part used for height adjustment)

Let me know if you end up getting the swift springs, i am interested in seeing how much of a difference they majke.

9krpmrx8

iTrader: (46)

I'm not sure, but people don't like to criticize stuff they buy because I guess they don't want to catch any flack for making a seemingly poor choice. But I think if more people did then certain items would not get hyped so much. But maybe Stance fixed this issue in the latest coil overs

I will say again though that their customer service has been top notch so that goes a long way.

paimon.soror

iTrader: (15)

we should try and get them on the forums to chime in. It would be interesting, i mean, aren't some of these issues actually safety concerns... we are lucky we have a large washer on the hub bolt, but if we didn't boy would a dislocated bushing cause some major havok. Not to mention the rust issue ... gunna be a fantastic time trying to move the spring perches around once they are rust welded on lol

9krpmrx8

iTrader: (46)

Yeah I can't imagine how they would look after a couple of years.

hoss -05

iTrader: (4)

Or after a winter of salted roads LOL sorry I had to pass the buck to you 9k. I'm sure you now better understand my decision to go with the FCM set up.

9krpmrx8

iTrader: (46)

It's all good, I like a challenge

paimon.soror

iTrader: (15)

I envision 9k 5 months from now with a mallet, a screwdriver, wd40, and lots of swearing.


dont ask why i chose those specific tools and scenario...just have them in your arsenal

hoss -05

iTrader: (4)

He pefers a nice big hammer over a mallet. Ask him about the battery terminals some time.

9krpmrx8

iTrader: (46)

At this point I have done so many suspension setups on RX-8's that I could do an RX-8 suspension swap with my eyes closed On the Stance/Powertrix I find that it is easier just to remove the rears to adjust them.

9krpmrx8

iTrader: (46)

5lb sledge and battery terminals, I don't see how that could be a problem A 5lb sledge also makes a great fender roller too.

paimon.soror

iTrader: (15)

Hahaha i hear ya, this was my first suspension install. Going into it i took my time and babied the entire process, but now I can really do it no problem. The issue you may run into is that the perches fuse together quite nicely, which is great, until you realize that your spanner wrenches and strength can no longer break the seal. So you gotta break out the hammer of thor and a screwdriver to crack them loose.

9krpmrx8

iTrader: (46)

Yeah mine were seized up a bit too, a pipe wrench and big screw driver through the lower bushings works wonders

J8635621

iTrader: (10)

I need this

9krpmrx8

iTrader: (46)

A pipe wrench won't damage the threads and will hold the top portion and a large screwdriver will give you the leverage to bust it loose. Also, some PB blaster would help too.

J8635621

iTrader: (10)

Yea I'm just too lazy to take the coilovers out YET AGAIN. It's riding good right now, so I'll just let it be until it starts squeaking again or something.

9krpmrx8

iTrader: (46)

Update:

Stance customer support is awesome. I really love that they stand behind their product. I think I'll stick with them. I will update of the swift springs info when I get it.

check it:

Quote:

Hello Scott,

We have updated the materials that we use in our bushings, I would be happy to send you a pair of new rear lower brackets under warranty. You should have those shortly.

Cheers,

Rob Riter
Sales Ambassador