Rear Suspension Diagram
#1
I'm Delaware Fast
Thread Starter
iTrader: (1)
Join Date: Dec 2007
Location: Blacksburg VA/Dover DE
Posts: 450
Likes: 0
Received 0 Likes
on
0 Posts
Rear Suspension Diagram
Can anyone post up a link of the RX-8 Suspension Diagram. I found the one for the front suspension but I can not find the one for the rear. Any info would be a great help.
BTW: I'm finishing my Tein S-Tech installation.
BTW: I'm finishing my Tein S-Tech installation.
#2
Grocery Getter
iTrader: (1)
To remove your rear shocks you need to remove the carpet inside your trunk. Remove the 4 14mm bolts hold the bracket on the top of the strut tower. The two 14mm at the base of the strut tower where it meets the body. Under there is a 12mm bolt going upwards. Remove the rear swaybar 12mm (this makes it easier to pull out the coil assmb). Undo the headlight leveling sensor 10mm. Remove one part of the endlink 14mm. The bolt thats on the bottom of the strut 17mm and finally the camber bolt at the end of the control arm, 19mm.
Make sure to make a fine mark on the fwd and aft cam so you get your alignment back 99%.
Thats about it.
Make sure to make a fine mark on the fwd and aft cam so you get your alignment back 99%.
Thats about it.
#3
I'm Delaware Fast
Thread Starter
iTrader: (1)
Join Date: Dec 2007
Location: Blacksburg VA/Dover DE
Posts: 450
Likes: 0
Received 0 Likes
on
0 Posts
To remove your rear shocks you need to remove the carpet inside your trunk. Remove the 4 14mm bolts hold the bracket on the top of the strut tower. The two 14mm at the base of the strut tower where it meets the body. Under there is a 12mm bolt going upwards. Remove the rear swaybar 12mm (this makes it easier to pull out the coil assmb). Undo the headlight leveling sensor 10mm. Remove one part of the endlink 14mm. The bolt thats on the bottom of the strut 17mm and finally the camber bolt at the end of the control arm, 19mm.
Make sure to make a fine mark on the fwd and aft cam so you get your alignment back 99%.
Thats about it.
Make sure to make a fine mark on the fwd and aft cam so you get your alignment back 99%.
Thats about it.
#4
Grocery Getter
iTrader: (1)
That would be the camber bolt. It should have like -- / | \ -- markings on it. Just pick the middle one and scribe onto the metal bracket.
If you can hold out today im installing someones coilovers and ill snap some pictures for you like a step by step.
#6
I'm Delaware Fast
Thread Starter
iTrader: (1)
Join Date: Dec 2007
Location: Blacksburg VA/Dover DE
Posts: 450
Likes: 0
Received 0 Likes
on
0 Posts
Holy ****...getting that shock out is RIDICULOUS. Hahaha...it gets stuck on the way out...pulling and screwing. If I could just move that damn endlink over an INCH...it would have dropped right out.
Damn.
Pics incoming.
Damn.
Pics incoming.
#9
I'm Delaware Fast
Thread Starter
iTrader: (1)
Join Date: Dec 2007
Location: Blacksburg VA/Dover DE
Posts: 450
Likes: 0
Received 0 Likes
on
0 Posts
Ok..it's all done and it looks fantastic. I will post pics up when I get off of work tomorrow. First time doing anything with suspension myself but I learned a whole lot and saved $400 avoiding the shop. Thanks everyone!!!
Thread
Thread Starter
Forum
Replies
Last Post
nowakm99
Series II Technical and Trouble shooting
1
10-09-2015 07:10 AM
To The Wonder
NE For Sale/Wanted
0
09-12-2015 12:35 PM