alelogman

I'm new here the experts are here and I want to learn more but the number of posts is mind boggling. I know I landed at the right place because the used engines were therejust by reading the comments posted here I'm going to gain tons of knowledge. Thanks guys!

cavemancan

I know your following me!

angeljoelv

lol...

cavemancan

I always loved this pic of your car!

Ross_Dawg

iTrader: (2)

love it

Vlaze

iTrader: (14)

That is the solution. My setup you quoted previously is 18x10 +28 all around which got me dead on flush for the rear and a slight poke on the front. That plastic on the top right of your pic is completely cut via dremel and shoved up in my car on the rears. The only thing the tires can possible brush is the plastic left over from grinding down the tab that connects the rear bumper to the fender which has reduced all the way to the fastener itself. Everything else was modified by cutting or grinding. I run my coil overs on the stiffer side of the setting as well.

If someone is running near the low 30's offset close to my +28 or less, you're going to need -2.5 camber or more to make this work. Mine are currently at -2.5.

For anything +35 or more offset with a 18x10, you should be clear using what I mentioned without needing too much negative camber.

TiffanyLillian

Hmm, i really like these.

9krpmrx8

iTrader: (46)

Does anyone know if all the center caps are in one box?

http://www.flickr.com/photos/9krpmrx8/5075936322/http://www.flickr.com/photos/9krpmrx8/5075936322/ by http://www.flickr.com/people/9krpmrx8/, on Flickr

angeljoelv

they are all in one box, and as you can imagine mine were in the last one I opened. So by the time I got to the 4th I was praying/crying they would be there.

2tone

iTrader: (3)

did you order these 9k??!!!!

Atilla

iTrader: (1)

^+1

when i was checkin' the box at the loading area i almost freaked out because i didn't find the center caps until i double checked the last box. They were tucked behind the wheel at the bottom of the box

The Reverend

iTrader: (1)

mine were in the first box

Atilla

iTrader: (1)

oh yeah? well...you're a f_ggot

The Reverend

iTrader: (1)

2tone

iTrader: (3)

ha ha ha hilarious tills

but seriously, did you guys know 9k was ordering these? he just got new volks! JEALOUS

The Reverend

iTrader: (1)

they are not his 2tone get some new inside rx8club informants

Atilla

iTrader: (1)

2tone: negative - iirc, he was holding them for another forum member

...unless he's a...BIG FAT LIAR

2tone

iTrader: (3)

ha ha i just opened this and saw his pic so i jumped to conclusions

ha ha oooooooh, suuure he's holding them for someone. if i was that someone, i'd hurry the f up and get them from 9k's grasp!!

9krpmrx8

iTrader: (46)

No these are Hoss-05's, I am just holding onto them for him for a couple of months. But I only opened one box and there were no center caps. I didn't want to open every box, but I guess I better just to make sure they are there.

WinningRX8Chick

I can't freaking wait... mine are in the process of being made/shipped.... Gunmetal 18x10 +42

adamwzl

iTrader: (3)

9k just open them and retap the box


then hoss can have the satisfaction of opening them first, but we would all know its a lie

Atilla

iTrader: (1)

^good choice

tire specs??

^That's like bonin' the wife before her wedding...that hurts bro...that hurts...

adamwzl

iTrader: (3)

hey gotta do what you gotta do. Hes getting free storage.

Atilla

iTrader: (1)

remind me never to let you kick it with my next gf...




...shiesty *** ***** fu....

WinningRX8Chick

Hankook Ventus V12 Evo 255/35/18 (preeeetty sure on the size...)

I was going to go with a +38 but Forgestar really pushed the +42 saying it's the best for RX-8s... *shrug*