Rebuilt engine does not sound good
#1
Rebuilt engine does not sound good
I have attached a video of my turbo rx8 just after rebuilding the engine. Please tell me what u think before i tow it to the shop that rebuilt the engine.
http://s32.photobucket.com/albums/d2...t=IMG_0195.mp4
http://s32.photobucket.com/albums/d2...t=IMG_0195.mp4
#2
Banned
iTrader: (3)
Pretty low idle vacuum there. (Less than 12" of mercury or so.)
The whistle is the jet air bleed. You can put a check valve on that, but it will still whistle at idle.
Have you measured the compression of the motor? Do it before you start beating on it. If you are using the e-Manage that came with the system, be very careful and don't alter the boost at all.
The whistle is the jet air bleed. You can put a check valve on that, but it will still whistle at idle.
Have you measured the compression of the motor? Do it before you start beating on it. If you are using the e-Manage that came with the system, be very careful and don't alter the boost at all.
#3
SARX Legend
iTrader: (46)
Honestly it's hard to tell but it doesn't sound too bad. What are you putting your hand on? Vacuum line? The ticking sounds like the SSV actuator ticking, it's a common issue. What codes are you getting for the CEL?
Mind you this video is a 4 port but the issue is eh same. I currently have this issue.
http://www.youtube.com/watch?v=8dIJVcxbBpE
I would recheck everything, make sure there is not a vacuum leak, etc.
Mind you this video is a 4 port but the issue is eh same. I currently have this issue.
http://www.youtube.com/watch?v=8dIJVcxbBpE
I would recheck everything, make sure there is not a vacuum leak, etc.
Last edited by 9krpmrx8; 07-07-2011 at 12:01 AM.
#5
SARX Legend
iTrader: (46)
Well my SSV actuator ticks (knocks, rattles) at idle. When I put my finger on it, it stops. It passes the vacuum test fine the shaft has play in it and it ticks/rattles at idle. But from his video I can't tell if that is the same sound or not.
#6
I feel the tick is coming from the engine more like a knock the video makes it sound better than it really is. I compression tested it i was getting 80 psi but my battery is deff weak had a charger on it but the reading are the same throughout the motor(motor cold). The emanate utimate is hooked up just trying to make sure everything is cool then ap. Im being very causious no load, no revs, no boost at all
#7
SARX Legend
iTrader: (46)
I feel the tick is coming from the engine more like a knock the video makes it sound better than it really is. I compression tested it i was getting 80 psi but my battery is deff weak had a charger on it but the reading are the same throughout the motor(motor cold). The emanate utimate is hooked up just trying to make sure everything is cool then ap. Im being very causious no load, no revs, no boost at all
I would have a proper compression test done (warm). Can't hurt to put you finger on the SSV acuator just to check. Mine freaked me out when it first started happening, I thought I threw a rod
#8
P0302 on 2 occasions but is not misfiring now. Stock plugs ls2 truck coils and new wires. Engine just just idles rough and the noise may be the ssv its coming from that area for sure.
#9
SARX Legend
iTrader: (46)
This is the vid I used to help me test my coils.
http://www.youtube.com/watch?v=2woQT1eOy8U
#12
Ill check the coils they are new but never kno, proper compression chech, and the ssv. Anything else i should look for it deff running rich the exhaust stinks like unburnt fuel and smokes missfire sounds probable mabe even causing the knocking sound
#15
SARX Legend
iTrader: (46)
Well with a midpipe and no cat, you will smell fuel all of the time, that is just how a uncatted rotary runs. The smoke is somewhat normal as well but should only be for a bit at startup and then go away. Different types of premix (if you are pemixing) will affect smell, smoke, etc. as well.
#17
SARX Legend
iTrader: (46)
http://www.youtube.com/watch?v=rSlqL...mbedded#at=104
Last edited by 9krpmrx8; 07-07-2011 at 10:53 AM.
#18
Ya put my finger on it and knock goes away between that my rattly exhaust tips and the lf wheels valvestem nut lose in the wheel makes it sound like a pos haa seems to be running good now im gonna get a new battery(any recommendations) and order ap through mm
#20
The shop that built the engine said use the emanage the turner there tunes kyle mohans fd rx8(i kno is a 13b rew) but veey rebutable tuner and has tuned several turbo renesis with emanage but all i hear is the emanage is garbage
#21
SARX Legend
iTrader: (46)
That guy may be a reputable RX-7 tuner but no one on the planet as tuned more 8's with than MM. MM may be difficult to deal with at times if you don't know how to follow instructions/listen but he is the Jedi master of RX-8 tuning.
#22
Just going for reliable was very hesitant with putting the turbo back on im not going for power just a fun car run 5 psi u kno if the cobb is the way to go ill do it the cobb had just came out after i put my kit on in 08 and engine blew up a week before i had money to get the cobb i dont wanna half *** anything this time around
Thread
Thread Starter
Forum
Replies
Last Post
Str8lineJKing
New Member Forum
24
07-22-2015 04:19 PM