Rebadging! Need some help helpful people
#1
The darkness lies within
Thread Starter
Join Date: Jun 2011
Location: Annapolis
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
Rebadging! Need some help helpful people
Hey guy's,
So partially because I'm forum-ly inept and I am still learning my way around this form I couldn't find this answer anywhere else. I'm finishing up work on my car most recently a MS spoiler and now my last task is to rebadge my truck. The previous owner debugged it and placed awkward plastic holders in the post holes.
My question is how do I remove these awkward plastic spacers and put in a rear badge? Also, where can I find a post badge on the internet? If it's easier I can just order one from the dealer (with post). The key is I want the post in. And I want it to be cheap.
THANKS FOR THE HELP
ShadowRotor
So partially because I'm forum-ly inept and I am still learning my way around this form I couldn't find this answer anywhere else. I'm finishing up work on my car most recently a MS spoiler and now my last task is to rebadge my truck. The previous owner debugged it and placed awkward plastic holders in the post holes.
My question is how do I remove these awkward plastic spacers and put in a rear badge? Also, where can I find a post badge on the internet? If it's easier I can just order one from the dealer (with post). The key is I want the post in. And I want it to be cheap.
THANKS FOR THE HELP
ShadowRotor
#2
Pics would help to determine the best way to remove the plastic fillers. I would drill'em out anyway since i am lazy.
You can buy the badges online or from the forum vendors like Mazmart etc. The badges already have the pins so you will just have to position them in the existing holes and double tape\glue them back on.
You can buy the badges online or from the forum vendors like Mazmart etc. The badges already have the pins so you will just have to position them in the existing holes and double tape\glue them back on.
#3
Surf Hard, Drive Hard
Join Date: Feb 2007
Location: Indialantic, Florida
Posts: 7,840
Likes: 0
Received 11 Likes
on
9 Posts
Yep, best place is probably www.onlinemazdaparts.com or www.finishlineperformance.com if you are in the states. Don't think Mazmart carries them ,but I could be wrong.
#4
The darkness lies within
Thread Starter
Join Date: Jun 2011
Location: Annapolis
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
Oh sorry. That makes a lot of sense, here are the pictures of the plastic fillers in the holes. I don't just want to yank them out and pull out my trunk as well.
And I did find a badge I'll be ordering it tomorrow.
And I did find a badge I'll be ordering it tomorrow.
#6
The darkness lies within
Thread Starter
Join Date: Jun 2011
Location: Annapolis
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
So, like just wrap the tape around the screwdriver, shove it under the caps and pull it out? I really don't wan to scratch it, and I refuse to pay to get a new badge installed.
#9
The darkness lies within
Thread Starter
Join Date: Jun 2011
Location: Annapolis
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
That's why I'd rather have the Mazda Badge. I'm thinking about painting it flat black and replacing these with that. My only reservation is that I'm not sure one flat black M would clash with my car.
#11
The darkness lies within
Thread Starter
Join Date: Jun 2011
Location: Annapolis
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
#12
Auto to manual swapped
Black emblems on a black car? Might as well not even have em and just fill in the holes lol. What I plan on doing is just leaving the M on and taking the left and right badges off then fill em like this
#19
The darkness lies within
Thread Starter
Join Date: Jun 2011
Location: Annapolis
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
I bet, I have a couple questions for you though,
Is the Renesis badge a whole badge or did you use the individual adhesive letters to spell it and did you do it yourself? If so what did you do with the holes from the old badges? I'm planning on doing the same thing, same badge but Shadow instead of renesis (that's my car's name). But I don't wont to send it to a shop, I just got her back
Is the Renesis badge a whole badge or did you use the individual adhesive letters to spell it and did you do it yourself? If so what did you do with the holes from the old badges? I'm planning on doing the same thing, same badge but Shadow instead of renesis (that's my car's name). But I don't wont to send it to a shop, I just got her back
#21
Redlined
iTrader: (5)
All the information you need is in this topic.
I wasnt the first one to do this -- i got the idea from bruce that did it first -- and yes it does cover up the holes
https://www.rx8club.com/series-i-exterior-appearance-body-kits-27/renesis-badge-rear-end-102238/
I wasnt the first one to do this -- i got the idea from bruce that did it first -- and yes it does cover up the holes
https://www.rx8club.com/series-i-exterior-appearance-body-kits-27/renesis-badge-rear-end-102238/
Thread
Thread Starter
Forum
Replies
Last Post
Audio Concepts ATL
New Member Forum
21
09-26-2021 01:59 PM
WingleBeast
Series I Wheels, Tires, Brakes & Suspension
22
05-23-2016 09:22 PM