LED 3rd Brakelight
#1
LED 3rd Brakelight
Have any of you installed an LED third brakelight on your RX8? If so, and you installed a load resistor, how many ohms and at what wattage did you use?
Thanksss
Thanksss
#3
Registered
iTrader: (5)
You don't need a load resistor for the LED brake light. In fact, it is recommended that you don't run a resistor on a constant-load circuit, such as a brake light or running light. The resistors are only necessary on your turn signals to prevent the rapid flash, lamp out indication. Just plug it in and you're good to go!
#4
You don't need a load resistor for the LED brake light. In fact, it is recommended that you don't run a resistor on a constant-load circuit, such as a brake light or running light. The resistors are only necessary on your turn signals to prevent the rapid flash, lamp out indication. Just plug it in and you're good to go!
#5
SARX Legend
iTrader: (46)
locally, we have three four people with the LED 3rd light and no one has ever had issues. Just use the rubber grommet from the OEM one because the one that comes with the light is too stiff.
I think this mod is a must, especially for the Series II guys.
I cannot embed pics in this sub forum but here you go.
http://farm2.static.flickr.com/1212/...e17726ab_b.jpg
http://farm2.static.flickr.com/1039/...6e681ccc_b.jpg
http://farm2.static.flickr.com/1117/...e1aa0a3e_b.jpg
I think this mod is a must, especially for the Series II guys.
I cannot embed pics in this sub forum but here you go.
http://farm2.static.flickr.com/1212/...e17726ab_b.jpg
http://farm2.static.flickr.com/1039/...6e681ccc_b.jpg
http://farm2.static.flickr.com/1117/...e1aa0a3e_b.jpg
#7
The RX-8 is missed
iTrader: (3)
Join Date: Aug 2005
Location: Houston, TX
Posts: 2,084
Likes: 0
Received 0 Likes
on
0 Posts
I dunno about that. I installed it and it caused by Traction Control and DSC lights to come on. I drove it out of town at night and the cruise control disengaged when I turned on my parking/headlights. When I removed the LED brakelight and re-installed the OEM, everything was fine again.
#10
SARX Legend
iTrader: (46)
Your light can't be different, they are all the same. In this vid he does not remove the rubber grommet but trust me, grungepup here in out group has installed a few of these and he does it the same each time and it comes out perfect.
http://www.youtube.com/watch?v=Ho3FgRVszdY
http://www.youtube.com/watch?v=Ho3FgRVszdY
#11
Wow I looked at that video before I bought the lamp, and that is the company that I purchased it from! Zonkspeed or something like that. I called them about this issue and they told me that I needed to get a load resistor and that I could purchase one from PepBoys or Autozone.... negative.
#12
SARX Legend
iTrader: (46)
I dunno man, PM grungepup. We have 5 RX-8's locally with the LED 3rd brake light and none of them have load resistors and I know grungepup and shinka-mami have had their lights for a few years now.
Last edited by 9krpmrx8; 07-12-2010 at 01:48 PM.
#13
Registered
iTrader: (5)
I dunno about that. I installed it and it caused by Traction Control and DSC lights to come on. I drove it out of town at night and the cruise control disengaged when I turned on my parking/headlights. When I removed the LED brakelight and re-installed the OEM, everything was fine again.
#14
I zoom therefore I am.
do you also have LEDs in any of your tail lights? the demands on the electrical system are different for LEDS and can cause issues with all kinds of other things
Thread
Thread Starter
Forum
Replies
Last Post
nowakm99
Series II Technical and Trouble shooting
1
10-09-2015 07:10 AM
jasonrxeight
RX-8's For Sale/Wanted
2
09-30-2015 01:53 PM