RX8Club.com

Notices
Series I Tech Garage The place to discuss anything technical about the RX-8 that doesn't fit into any of the categories below.

How to change to clear corners?

Thread Tools
 
Rate Thread
 
Old Jun 28, 2010 | 05:43 PM
Share
  #1  
nickraft14's Avatar
nickraft14
Thread Starter
Registered User
 
Joined: May 2010
Posts: 62
Likes: 0
How to change to clear corners?
Where do you buy clear corners and how would I put
Them on?
Reply
0
Old Jun 28, 2010 | 05:49 PM
Share
  #2  
Bullitt's Avatar
Bullitt
In the pipe five by five.
iTrader: (7)
 
Joined: Oct 2009
Posts: 947
Likes: 1
From: Causeway Tollbooth
https://www.rx8club.com/series-i-do-yourself-forum-73/diy-side-marker-clear-corner-lights-installation-10379/

It's really gonna help if you start searching the site. It's just about all on here already.
Reply
0
Old Jun 28, 2010 | 06:21 PM
Share
  #3  
BlackRX82006's Avatar
BlackRX82006
Pedobear approved
iTrader: (1)
 
Joined: May 2007
Posts: 1,071
Likes: 0
From: Phoenix, AZ
Originally Posted by nickraft14
Where do you buy clear corners and how would I put
Them on?
Take a pry bar to get them off. Then you take a hammer to put the clear corners back on. Be careful and make sure you do not use a rubber hammer. Use a big construction sledgehammer.
Reply
0
Old Jun 28, 2010 | 09:17 PM
Share
  #4  
RX8pwnage's Avatar
RX8pwnage
RX8. Yeah, I get it.
iTrader: (1)
 
Joined: May 2009
Posts: 456
Likes: 0
From: West Lafayette, IN
Originally Posted by nickraft14
Where do you buy clear corners and how would I put
Them on?
Series 2 RX8s dont have "corners" so posting in the Series 2 forum isnt gonna help you much.
Reply
0
Old Jun 28, 2010 | 09:19 PM
Share
  #5  
Spinning Sushi's Avatar
Spinning Sushi
I <3 Sushi
iTrader: (21)
 
Joined: Aug 2006
Posts: 3,967
Likes: 4
From: SoCal
Originally Posted by BlackRX82006
Take a pry bar to get them off. Then you take a hammer to put the clear corners back on. Be careful and make sure you do not use a rubber hammer. Use a big construction sledgehammer.
It was so easy thanks to your instructions! I didn't have a sledgehammer so I had to use a jackhammer.
Reply
0
Old Jun 28, 2010 | 09:35 PM
Share
  #6  
Bullitt's Avatar
Bullitt
In the pipe five by five.
iTrader: (7)
 
Joined: Oct 2009
Posts: 947
Likes: 1
From: Causeway Tollbooth
Originally Posted by RX8pwnage
Series 2 RX8s dont have "corners" so posting in the Series 2 forum isnt gonna help you much.
These look pretty decent, though. http://kalecoauto.com/index.php?main...products_id=37
Reply
0
Old Jun 28, 2010 | 10:20 PM
Share
  #7  
Tweek's Avatar
Tweek
RobotsToRobots.com
 
Joined: Jan 2010
Posts: 455
Likes: 0
From: South Florida
Originally Posted by Bullitt
Are they serious?
Reply
0
Old Jun 28, 2010 | 10:28 PM
Share
  #8  
Bullitt's Avatar
Bullitt
In the pipe five by five.
iTrader: (7)
 
Joined: Oct 2009
Posts: 947
Likes: 1
From: Causeway Tollbooth
^Yeah, scope these:
http://kalecoauto.com/index.php?main...&products_id=8
http://kalecoauto.com/index.php?main...products_id=28
Reply
0
Old Jun 29, 2010 | 11:24 AM
Share
  #9  
RXeckless's Avatar
RXeckless
Rotorless
iTrader: (5)
 
Joined: Jul 2008
Posts: 1,135
Likes: 4
From: Delhi, ON Canada
I'm ordering two of everything on this site, just in case my sledgehammer does not work the first time.
Reply
0
Old Jun 29, 2010 | 01:02 PM
Share
  #10  
Huey52's Avatar
Huey52
Registered Zoom Zoomer
iTrader: (2)
 
Joined: Apr 2006
Posts: 4,089
Likes: 6
From: New England
It's a good thing you posted now, because in a little over two months the 7-year statute of limitations on this question will expire.

Did you really think this has never been done before?

Originally Posted by nickraft14
Where do you buy clear corners and how would I put
Them on?
Reply
0
Old Jul 1, 2010 | 06:00 PM
Share
  #11  
Renesis 8's Avatar
Renesis 8
Registered
 
Joined: Aug 2007
Posts: 75
Likes: 0
From: Apple Valley, Minnesota
Wow
Reply
0
Old Jul 2, 2010 | 12:00 AM
Share
  #12  
yiksing's Avatar
yiksing
the giant tastetickles
 
Joined: Sep 2005
Posts: 2,758
Likes: 0
From: in the basement
Clear corners swap is slightly more difficult than an engine swap but not as difficult as a battery swap.
Reply
0
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Blown oil seal?
WranglerFan
New Member Forum
4
May 31, 2022 07:51 AM
oil in intake and power loss at high rpm
WranglerFan
New Member Forum
4
Nov 5, 2017 09:35 AM
Loss of power at exactly 7.5k RPMS
DVerdeyen
Series I Trouble Shooting
6
Sep 13, 2015 11:19 AM
DIY - Corksport License Plate Frame Install Guide
projectr13b
Series I Do It Yourself Forum
1
Sep 6, 2015 01:04 PM
{WTB} Wtb: Gen 1 clear side marker/corner
blkswan
West For Sale/Wanted
0
Sep 2, 2015 10:04 PM
Tags
Back to Subforum
Series I Tech Garage
View Next Unread
What is your vacuum readings?



You have already rated this thread Rating: Thread Rating: 0 votes, average.
Show Printable Version
Email this Page

Advanced Search

All times are GMT -5. The time now is 11:50 AM.