3 Rotor RX8 PR
02-22-2009, 09:26 AM
#1251
Guest
Posts: n/a
[QUOTE=rgonza;2679528]
Can you please send me this??? PLEASE 
....
PM please.
Moe.
im digin the setup. About how much would the type of setup your running will set me back and would i go thru FB performace to purshase the transmission ?[/QU
To whats engine you would plan to install it? Renesis, REW 13b, cosmo, 20b. and kinds of mods you plans to do? the 4stb from FB performance alone would work good for your application alone now if you plans to runs more radical HP i can send to the the total recipe to run it wild like F1 Does.
Regards
Rgonza
To whats engine you would plan to install it? Renesis, REW 13b, cosmo, 20b. and kinds of mods you plans to do? the 4stb from FB performance alone would work good for your application alone now if you plans to runs more radical HP i can send to the the total recipe to run it wild like F1 Does.
Regards
Rgonza
....PM please.
Moe.
Last edited by Kazuma; 10-03-2009 at 03:26 AM.
Pics
04-03-2009, 04:38 PM
#1261
Rob gonzalez
Thread Starter
Join Date: Dec 2005
Location: Naranjito, Puerto Rico
Posts: 356
Likes: 0
Received 0 Likes
on
0 Posts
Up to 530 RWHP @ 22 Psig boost with Methanol/water injection on premiun pump gas, the blue one has 534 Rwhp
QUOTE=OneEvilRx8;2949892]Roberto, what kind of RWHP you got out of the 13REW?[/QUOTE]
QUOTE=OneEvilRx8;2949892]Roberto, what kind of RWHP you got out of the 13REW?[/QUOTE]
04-17-2009, 08:34 PM
#1262
Swift Speed
iTrader: (1)
Join Date: May 2008
Location: Phillips Ranch/Diamond Bar, Ca
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
Here's the pic's of my car with Turbocharged 20B 3 Rotor engine from mazda JDM cosmo Here,s The Modifications List and setup.
Street Ported 20B 3 Rotor Engine
Innovative GTB 76 dual ball bearing turbocharger
2 mm. Kirbee Apex Seals
Custom Exhaust Manifold
Fluidyne Aluminum Radiator
spearco Intercooler
Tial 50 mm. Blowoff valve
Turbonetics waste gate
Modified 6 Speed tranny
Steel drive shaft
Custon harden steel 52 mm.rear haft shaft
Exedy Dual disc clutch
E Boost boost controller
2 In line Bosh 044 fuel pumps
Heavy Duty Oil coolers
3.90 rearend gear
Microtech EMS lt-12s
6 MSD blaster coils 8106
Custom 3.5 Exhaust system
Aereomotive Fuel regulator
Aereomotive Electronic Fuel Pump Speed Controller
3 1000 cc Primaries Fuel Injectors
3 1660 cc Secundary Fuel Injectors
Custom Fuel Rails
The results of this combination = 657 RWHP @ 9600 RPM @ 14 PSI Boost
rgonza
Street Ported 20B 3 Rotor Engine
Innovative GTB 76 dual ball bearing turbocharger
2 mm. Kirbee Apex Seals
Custom Exhaust Manifold
Fluidyne Aluminum Radiator
spearco Intercooler
Tial 50 mm. Blowoff valve
Turbonetics waste gate
Modified 6 Speed tranny
Steel drive shaft
Custon harden steel 52 mm.rear haft shaft
Exedy Dual disc clutch
E Boost boost controller
2 In line Bosh 044 fuel pumps
Heavy Duty Oil coolers
3.90 rearend gear
Microtech EMS lt-12s
6 MSD blaster coils 8106
Custom 3.5 Exhaust system
Aereomotive Fuel regulator
Aereomotive Electronic Fuel Pump Speed Controller
3 1000 cc Primaries Fuel Injectors
3 1660 cc Secundary Fuel Injectors
Custom Fuel Rails
The results of this combination = 657 RWHP @ 9600 RPM @ 14 PSI Boost
rgonza
05-26-2009, 07:54 PM
#1265
Registered User
Join Date: Feb 2005
Location: Manati, Puerto Rico
Posts: 607
Likes: 0
Received 0 Likes
on
0 Posts
I'm selling my 3 rotor RX8........................
https://www.rx8club.com/showthread.p...21#post3039821
If any one have interest send me PM or emails to valvila@valvila.com
please only serious buyers.
Manuel
https://www.rx8club.com/showthread.p...21#post3039821
If any one have interest send me PM or emails to valvila@valvila.com
please only serious buyers.
Manuel
10-02-2009, 10:46 PM
#1269
Hey man, how's it going...I know where he cut...I can show you, Rgonza is really busy, he might not be able to answer.
You can also search for Angel's thread called "surgery has begun" in the multimedia section, there are pics of the crossmember cut and re-welded in that thread.
Call me and I can tell you.
Chris
You can also search for Angel's thread called "surgery has begun" in the multimedia section, there are pics of the crossmember cut and re-welded in that thread.
Call me and I can tell you.
Chris
10-03-2009, 01:03 AM
#1270
Cool thanks Chris.
You know me lol lots of research before I jump in.
Chris: Wife gave me the green light on the purchasing the 20b. Happy man right now
You know me lol lots of research before I jump in.
Chris: Wife gave me the green light on the purchasing the 20b. Happy man right now
Last edited by Speedrx8er; 10-03-2009 at 02:31 AM.
03-05-2010, 05:55 PM
#1273
Registered User
Join Date: Mar 2010
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
Boricuas tengo un problema. La luz del dash prende intermitente en mi rx-8 y la computadora dice es el shaft position sensor lo cual cambie pero nada, esta igual. Le cambie las bujias pero esta raro que estaban de diferente manera de lo que me dijo el auto parts. que creen ustedes ??????
03-06-2010, 02:26 PM
#1274
Rob gonzalez
Thread Starter
Join Date: Dec 2005
Location: Naranjito, Puerto Rico
Posts: 356
Likes: 0
Received 0 Likes
on
0 Posts
Saludos, Verificas las bobinas"Ignition Coils"si tienen una mancha blanca por las parte posterior tienes que reeplazarlas, o verifica el throtler body.
Saludos
Rgonza
Saludos
Rgonza
Boricuas tengo un problema. La luz del dash prende intermitente en mi rx-8 y la computadora dice es el shaft position sensor lo cual cambie pero nada, esta igual. Le cambie las bujias pero esta raro que estaban de diferente manera de lo que me dijo el auto parts. que creen ustedes ??????
